Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Mon May 01, 2017 12:36 pm
Use the code I added in his guide as some of the buttons on his code were not used in my code so a few buttons are not wired in code.
sudomod
How to Program Helder's All in One GBZ PCB with Arduino IDE
Page 6 of 7
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Sun Jan 21, 2018 3:16 pm
Hey, Is there a way that I could do this without the the pin header, because I'm not clear on how I'd do it otherwise
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Tue Jan 23, 2018 10:53 pm
You just need to solder a usb wire like I already told you in the other thread then use a wire to touch the reset pin on the 6pin header holes to a GND to initiate a reset.
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Wed Jan 24, 2018 1:07 am
Oh ok so the pin header just makes it easier
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Thu Feb 15, 2018 11:46 pm
I'm having trouble installing the sparkfun driver. My computer recognizes that its plugged in but doesn't show it as a controller. I updated the drivers and directed it to the files given but it says everything is up to date but still doesn't show the sparkfun pro micro. Should I just continue to the next step or am I missing something?
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Tue Feb 20, 2018 11:16 pm
If you're using my board then unless it's one of very older black boards there is no more sparkfun driver/bootloader used so you should choose the 5v Leonardo as your board.
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Tue Aug 21, 2018 4:40 pm
Helder! The pics in this are not showed up. I want to programme my AIO board. Please help~
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Sat Dec 22, 2018 2:13 am
Hello everybody, I have exactly the same problem. Was this a solution found? Thanks and best regardsSwingeyP wrote: ↑Sat Aug 13, 2016 9:09 amHello @Helder,
Ok.
I reconnected the USB lead as I had originally and hooked it up to my Win10 PC.
All I see is the USB Not recognised error message popup and the device shown as :
'Unknown USB Device (Port Reset Failed)' in the Universal Serial Bus Controllers list.
I have tried swapping the white and green wires but when I do this nothing is detected at all (makes sense)
So, nothing detected by the Win10 PC.
IMG_3405.JPG
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Sun Dec 23, 2018 12:57 am
hey, can nobody help me?Macx wrote: ↑Sat Dec 22, 2018 2:13 amHello everybody, I have exactly the same problem. Was this a solution found? Thanks and best regardsSwingeyP wrote: ↑Sat Aug 13, 2016 9:09 amHello @Helder,
Ok.
I reconnected the USB lead as I had originally and hooked it up to my Win10 PC.
All I see is the USB Not recognised error message popup and the device shown as :
'Unknown USB Device (Port Reset Failed)' in the Universal Serial Bus Controllers list.
I have tried swapping the white and green wires but when I do this nothing is detected at all (makes sense)
So, nothing detected by the Win10 PC.
IMG_3405.JPG
Re: How to Program Helder's All in One GBZ PCB with Arduino IDE
Posted: Sun Dec 23, 2018 10:55 am
Macx wrote: ↑Sun Dec 23, 2018 12:57 amhey, can nobody help me?Macx wrote: ↑Sat Dec 22, 2018 2:13 amHello everybody, I have exactly the same problem. Was this a solution found? Thanks and best regardsSwingeyP wrote: ↑Sat Aug 13, 2016 9:09 amHello @Helder,
Ok.
I reconnected the USB lead as I had originally and hooked it up to my Win10 PC.
All I see is the USB Not recognised error message popup and the device shown as :
'Unknown USB Device (Port Reset Failed)' in the Universal Serial Bus Controllers list.
I have tried swapping the white and green wires but when I do this nothing is detected at all (makes sense)
So, nothing detected by the Win10 PC.
IMG_3405.JPG
have you had a look here....
https://sudomod.com/forum/viewtopic.php?f=52&t=1185
there's a high chance this has been covered and hopefully resolved there.....
.