Did you print it with my suggested settings on the first post? If you did those post should be solid plastic except for the hole. I've tested it with just Gb screws and unscrewed them maybe 5 or six times and they were still good. You could use bigger screws now or do inserts still.valinhorn wrote:I used the original screws and they worked the first time, but I had to re-open my case and now they aren't grabbing so I was hoping I could add in the inserts but keep using the same screws. I will figure something out.HoolyHoo wrote:If you decide to use the brass inserts then m2 screws are needed. Original case screws will not work. You don't need the inserts really unless you plan on opening your case multiple times. If you just use the original screws that came with your case they will work with the bracket as they are made for threading into plastic. They will be tight the first time you screw them. It was designed this way to give it strength. I would screw them in first before installing bracket to make the first threads needed in the plastic.valinhorn wrote:I had a question on the screw inserts. Is it possible to get these working with the original case screws? I can't seem to find what size the original screws are but it would be great if we could make the bracket work with them.
[For Sale]HoolyHoo's AIO bracket for Kite's Circuit Sword Board
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
I had shapeways print it, since I had a good deal through them, so I didn't have control over the settings. I am guessing inserts are going to be my best bet now. Thanks for your help.HoolyHoo wrote: Did you print it with my suggested settings on the first post? If you did those post should be solid plastic except for the hole. I've tested it with just Gb screws and unscrewed them maybe 5 or six times and they were still good. You could use bigger screws now or do inserts still.
- drafterITA
- Posts: 120
- Joined: Fri Feb 24, 2017 8:15 am
- Location: Italy
- Has thanked: 66 times
- Been thanked: 19 times
- Contact:
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
Hello!
thanks for creating this part, it will be very useful when I'll start the SAIO build I have in mind for the future
I got the screen without button wells and a set of 4 brass insert and screws, will it be possible to pack everything together in the same envelope?
thank you so much!
thanks for creating this part, it will be very useful when I'll start the SAIO build I have in mind for the future
I got the screen without button wells and a set of 4 brass insert and screws, will it be possible to pack everything together in the same envelope?
thank you so much!
Cheers!
drafterITA
drafterITA
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
Yes. That will not be a problem.drafterITA wrote:Hello!
thanks for creating this part, it will be very useful when I'll start the SAIO build I have in mind for the future
I got the screen without button wells and a set of 4 brass insert and screws, will it be possible to pack everything together in the same envelope?
thank you so much!
- WoodMill
- Posts: 181
- Joined: Tue Sep 06, 2016 11:57 am
- Location: Indianapolis, Indiana, USA
- Has thanked: 21 times
- Been thanked: 29 times
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
Very cool. Had my SAIO for a while now, but have been holding off building it because I knew some people would make things much easier. I was dreading re-using the same posts after skimming through the instructions.
Thanks HooluHoo!
Has anyone else made anything else that goes along with the SAIO?
Thanks HooluHoo!
Has anyone else made anything else that goes along with the SAIO?
Follow my Youtube Vlog about Filmmaking
https://www.youtube.com/playlist?list=P ... P0H6UZe1ds
https://www.youtube.com/playlist?list=P ... P0H6UZe1ds
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
Just put through an order Massive thanks for making this available!
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
I printed your screen bracket and noticed that the bottom screw posts have about a 1/4 inch gap between them and the back of the case. Is there a reason for this?
- Attachments
-
- 20170328_170443.jpg (3.14 MiB) Viewed 9197 times
-
- 20170328_170417.jpg (3.94 MiB) Viewed 9197 times
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
If it touched that post it would interfere with Kites daughter board and not close all the way. The other side is the same way in case you used original GB cartridge holder which has the same height. If you look at the bracket you will notice that the two post on the volume/USB side are slightly shorter. That is by design to accommodate that daughter board that gets sandwiched between the main board and the case post.Kalen wrote:I printed your screen bracket and noticed that the bottom screw posts have about a 1/4 inch gap between them and the back of the case. Is there a reason for this?
Re: HoolyHoo's AIO bracket for Kite's SAIO Board
HoolyHoo wrote:If it touched that post it would interfere with Kites daughter board and not close all the way. The other side is the same way in case you used original GB cartridge holder which has the same height. If you look at the bracket you will notice that the two post on the volume/USB side are slightly shorter. That is by design to accommodate that daughter board that gets sandwiched between the main board and the case post.Kalen wrote:I printed your screen bracket and noticed that the bottom screw posts have about a 1/4 inch gap between them and the back of the case. Is there a reason for this?
Ok cool. Thanks for the help and all your hard work making this.
Who is online
Users browsing this forum: No registered users and 1 guest