Which Version Screen Do I Have And How to Convert It?

Pepe_Silvia · Post by **Pepe_Silvia** » Fri Feb 03, 2017 4:05 pm

Okay so I took the board off the screen and saw this on the back. Do I just connect that 5V to the DC12 and it will run 5V?

n.marek · Post by **n.marek** » Fri Feb 03, 2017 4:07 pm

Yeah, that looks promising!
Just a tip for the soldering, don't strip the wires that long - you stripped like 1cm or more of the red wire. Strip them short, it's less likely the will touch each other!
And if you can push the wire through a hole, push it almost all the way through - to the end of the stripped part. And then cut off what's coming out from the other side, after you solder it in.

Pepe_Silvia · Post by **Pepe_Silvia** » Fri Feb 03, 2017 4:24 pm

n.marek wrote:Yeah, that looks promising!
Just a tip for the soldering, don't strip the wires that long - you stripped like 1cm or more of the red wire. Strip them short, it's less likely the will touch each other!

Yeah I'm a noob so I'm working on it. Also this happened so I guess this isn't a pointo I can solder to? Or maybe I'm just doing something wrong and I fucked it up

n.marek · Post by **n.marek** » Fri Feb 03, 2017 4:33 pm

https://www.youtube.com/watch?v=oqV2xU1fee8
or this one
https://www.youtube.com/watch?v=Qps9woUGkvI
Here's on of many videos on how to solder, maybe check that first and practice it.
What happened there? Did you burn the board? I can't tell if it's the flux or something else.

Pepe_Silvia · Post by **Pepe_Silvia** » Fri Feb 03, 2017 4:35 pm

n.marek wrote:https://www.youtube.com/watch?v=oqV2xU1fee8
Here's on of many videos on how to solder, maybe check that first and practice it.
What happened there? Did you burn the board? I can't tell if it's the flux or something else.

I'm not sure, it just happened when I tried to put some solder on there. I guess I burned it?

n.marek · Post by **n.marek** » Fri Feb 03, 2017 4:39 pm

I can't tell the condition of the pad underneath. Practise the soldering first, and then we get back to this.
I think you should be able to locate the 5V on the opposite side of the board, it must be one of the chips, so if you can find that, we can still do this. But don't do it before you can solder properly!

Pepe_Silvia · Post by **Pepe_Silvia** » Fri Feb 03, 2017 4:41 pm

n.marek wrote:I can't tell the condition of the pad underneath. Practise the soldering first, and then we get back to this.
I think you should be able to locate the 5V on the opposite side of the board, it must be one of the chips, so if you can find that, we can still do this. But don't do it before you can solder properly!

Yeah I'm going to practice for now. Thanks for the help!

Brett82 · Post by **Brett82** » Fri Feb 03, 2017 9:21 pm

do you have multimeter if so with the board powered with 12v can you measure the point I have indicated??

: 1486074266677-99549417.jpg (1.86 MiB) Viewed 8368 times

christair1 · Post by **christair1** » Sat Feb 04, 2017 12:38 am

Hello, I have this same screen. With the red cable only only connected to the rear 5v port.I am getting a very light image. No back light. Should I connect back to 12v and run a jumper cable to 5v ? Thanks for any help.

DannyJK · Post by **DannyJK** » Sun Feb 05, 2017 12:58 am

Here ya go! I just had to do this board the other day. Just about to head to bed, but I figured I would fire up Photoshop to help out a fellow Sudomodder.

YOU'RE WELCOME!!! Hope this helps you and I didn't reply too late.

Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Re: Which Version Screen Do I Have And How to Convert It?

Who is online