Search found 55 matches
- Mon Oct 16, 2017 9:50 am
- Forum: Resolved Issues (mintyPi)
- Topic: [Solved] Microlipo LEDs staying on
- Replies: 22
- Views: 21719
- Mon Oct 16, 2017 9:38 am
- Forum: Resolved Issues (mintyPi)
- Topic: [Solved] Microlipo LEDs staying on
- Replies: 22
- Views: 21719
Re: Microlipo LEDs staying on
Additional information, I had a closing issue (made a thread about it on this forum) as well as no audio. I figured pop it open and check the USB audio card and then check the 3d printed hinge. Sure enough the + power wire on the usb audio card was nearly torn off on the USB card end. No big deal, r...
- Mon Oct 16, 2017 9:08 am
- Forum: Support (mintyPi)
- Topic: [Not Solved]Closing the tin "sticks"
- Replies: 5
- Views: 4375
Re: Closing the tin "sticks"
Found the issue. The edge of the tin was slightly bent (don't know when that happened?) near the 3d printed hinge. It was causing the 3d printed hinge to get stuck under the bent part when it closed fully and putting strain on the pi during opening and closing. Thanks for the reply though! Wrong wr...
- Mon Oct 16, 2017 9:02 am
- Forum: Resolved Issues (mintyPi)
- Topic: [Solved] Microlipo LEDs staying on
- Replies: 22
- Views: 21719
[Solved] Microlipo LEDs staying on
Been troubleshooting some power issues and had the pcb up so I could examine cabling. I figured I'd plug it in to charge since maybe the battery was just dead or something. It started charging and didnt seem to have an issue. Looked down and both LED's were on so I unplugged it. But both stayed on a...
- Sun Oct 15, 2017 6:24 pm
- Forum: Support (mintyPi)
- Topic: [Not Solved]Closing the tin "sticks"
- Replies: 5
- Views: 4375
[Not Solved]Closing the tin "sticks"
I didn't know where to post this but it seemed appropriate here. I have my minty pi assembled but I have a problem opening it. When I close it there is no issue really. When I try to open it the left side sticks a bit and is extremely hard to open. So hard that I've actually bent the hinge a little....
- Sun Oct 15, 2017 9:02 am
- Forum: Show-off Corner (mintyPi)
- Topic: Fresh pi
- Replies: 3
- Views: 4134
Fresh pi
The outside isn't bad. Pretty basic.
The inside has a nice little flourish. Enamel paint to make the symbol pop. Silver leaf and Cobalt raspberry.
- Thu Oct 12, 2017 12:02 pm
- Forum: For Sale/Trade
- Topic: [For Sale, Preorder] DMG pre-cut cases
- Replies: 438
- Views: 335641
- Wed Oct 11, 2017 1:43 pm
- Forum: Support (mintyPi)
- Topic: White screen
- Replies: 78
- Views: 58516
Re: White screen
DC looks like it doesn't have enough solder. Did you see my last post on the previous page? Check the 4 gpio that I mentioned. My screen was exactly like that until I made sure to press the soldering iron deep into each opening and apply a *very* little bit more solder to each. Edit: also, you have ...
- Tue Oct 10, 2017 11:32 am
- Forum: Support (mintyPi)
- Topic: White screen
- Replies: 78
- Views: 58516
- Mon Oct 09, 2017 6:27 pm
- Forum: Support (mintyPi)
- Topic: White screen
- Replies: 78
- Views: 58516