Search found 15 matches

by kakan
Fri Jul 29, 2016 7:01 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: Kilren's No-OEM parts build [Complete]
Replies: 30
Views: 16278

Re: Kilren's No-OEM parts build [Complete]

How is your cartride reader holding up? I had to cut mine down a little more but I'm worried it won't hold that great. You're talking just of the Nintendo ds replacement part right (super tired :-P)? I used a small piece of perf board underneath to give it a little support and then I used only 5-mi...
by kakan
Fri Jul 29, 2016 12:04 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: Kilren's No-OEM parts build [Complete]
Replies: 30
Views: 16278

Re: Kilren's No-OEM parts build [Complete]

How is your cartride reader holding up? I had to cut mine down a little more but I'm worried it won't hold that great.
by kakan
Thu Jul 28, 2016 12:46 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: DirtyBeagles Gameboy Pi2 [95% Completed]
Replies: 45
Views: 17772

Re: DirtyBeagles Gameboy Pi2 [95% Completed]

Looking for some assistance on building a battery like Razor did on his post (http://www.sudomod.com/forum/viewtopic.php?f=9&t=76). I purchases the same battery and the same overcharge protection the only difference is that I purchased the batteries with tabs. The Tabs are covered in rubber. I am w...
by kakan
Sun Jul 24, 2016 11:25 am
Forum: Raspberry Pi
Topic: Resolution
Replies: 7
Views: 4593

Re: Resolution

Framebuffer_width= Framebuffer_height= Sets the resolution of the screen. I guess what you are looking for is overscan (to get the picture smaller/bigger towards the edge of the display) overscan_left= overscan_right= overscan_top= overscan_bottom= Also be sure that you put it in /boot/config.txt
by kakan
Sat Jul 23, 2016 1:36 pm
Forum: General Hardware
Topic: Step up module
Replies: 9
Views: 2485

Re: Step up module

I would think having two step up converters in a series will introduce even more distortion that perhaps may give the screen weird artifacts.
by kakan
Thu Jul 21, 2016 6:14 pm
Forum: General Chat (Game Boy Zero)
Topic: Any advice for modifying screen?
Replies: 10
Views: 3314

Re: Any advice for modifying screen?

Flux is your best friend, smear that thing on. I have never used flux before, just flux cored solder. I guess I'll order some. Do you put it everywhere apart from the leg of the chip? Yes I usually smear it on in the area I'm working on. I just do what @Quatrerwin does but also adding flux, After t...
by kakan
Thu Jul 21, 2016 1:41 pm
Forum: General Chat (Game Boy Zero)
Topic: Any advice for modifying screen?
Replies: 10
Views: 3314

Re: Any advice for modifying screen?

Flux is your best friend, smear that thing on.
by kakan
Mon Jul 18, 2016 1:25 pm
Forum: General Chat (Game Boy Zero)
Topic: USB problems with GBZ
Replies: 11
Views: 5437

Re: USB problems with GBZ

Data sheets says it should be supported. Did you try using it before desoldering the usb ports?
by kakan
Mon Jul 18, 2016 7:22 am
Forum: General Chat (Game Boy Zero)
Topic: USB problems with GBZ
Replies: 11
Views: 5437

Re: USB problems with GBZ

Have you checked if the usb chipset is supported with the raspberry pi?
by kakan
Sat Jul 09, 2016 9:40 am
Forum: General Chat (Game Boy Zero)
Topic: [Fixed] Blurry video
Replies: 6
Views: 3346

Re: Blurry video

Do you have a picture of your soldering?