I have sent an email and a PM a week ago to Wermy but haven't heard anything back, which is why I asked here. I can try again.
Search found 26 matches
- Fri Mar 09, 2018 12:36 pm
- Forum: For Sale/Trade
- Topic: [FOR SALE] Updated 3d-Printed mintyPi Parts
- Replies: 45
- Views: 41316
Re: [FOR SALE] Updated 3d-Printed mintyPi Parts
- Thu Mar 08, 2018 1:02 am
- Forum: For Sale/Trade
- Topic: [FOR SALE] Updated 3d-Printed mintyPi Parts
- Replies: 45
- Views: 41316
Re: [FOR SALE] Updated 3d-Printed mintyPi Parts
How do we get in contact with you for custom colors?
Jake
Jake
- Wed Mar 07, 2018 12:47 am
- Forum: For Sale/Trade
- Topic: [For Sale] DMG Buttons Shoulder Bracket
- Replies: 180
- Views: 134209
Re: [For Sale] DMG Buttons Shoulder Bracket
paypal links are back up! sales are good to go! If you were one of the people who were on back order, you packages are already out the door as of today, so all previous orders should now be in the mail. Thanks for your patience ! Erik, I sent an email to you from the site about CS board compatible ...
- Wed Feb 28, 2018 11:32 am
- Forum: For Sale/Trade
- Topic: MintyPi 2.0 for sale
- Replies: 9
- Views: 8902
- Wed Feb 28, 2018 1:17 am
- Forum: Support (mintyPi)
- Topic: No Boot after assembly
- Replies: 8
- Views: 4500
Re: No Boot after assembly
But open it back up and make sure your soldered wires are where they are supposed to be. Always solder and then tug to make sure your joint is good.
- Wed Feb 28, 2018 1:16 am
- Forum: Support (mintyPi)
- Topic: No Boot after assembly
- Replies: 8
- Views: 4500
Re: No Boot after assembly
Take a look at your power switch. A bad solder connection on it is realllllly easy to short power to the switch case, and when you close it up, it will ground out on the tin.
- Wed Feb 28, 2018 12:51 am
- Forum: General Chat (Game Boy Zero)
- Topic: Status LEDs / drilled holes on case or cartridge
- Replies: 3
- Views: 2360
Re: Status LEDs / drilled holes on case or cartridge
Hi guys I'm doing research into builds where people have drilled four small holes in the top of their case, or sometimes in the cartridge at the back, and mounted the four status LEDs of the kite board. I remember one thread mentioning taping down the case with kapton tape? Modifying the HoolyHoo b...
- Fri Feb 23, 2018 10:52 pm
- Forum: For Sale/Trade
- Topic: [For Sale]HoolyHoo's AIO bracket for Kite's Circuit Sword Board
- Replies: 605
- Views: 761088
Re: [For Sale]HoolyHoo's AIO bracket for Kite's SAIO Board
I got my brackets with the PSP joystick setup. I am getting ready to assemble the circuit sword, and I notice the holes in the bracket for the LEDs are pointing towards the face of the GB case. Not the top. How is this supposed to work, as Kites guide shows the LED holes pointing up?
- Fri Feb 16, 2018 8:38 pm
- Forum: For Sale/Trade
- Topic: MintyPi 2.0 for sale
- Replies: 9
- Views: 8902
MintyPi 2.0 for sale
For sale:
Peppermint MintyPi 2.0
All silicone wire
32gb Sandisk Ultra Class 10 SD card
Kapton taped connections
Thermal mat between battery and Raspberry Pi
Asking $250 shipped in the US
Thanks!
Peppermint MintyPi 2.0
All silicone wire
32gb Sandisk Ultra Class 10 SD card
Kapton taped connections
Thermal mat between battery and Raspberry Pi
Asking $250 shipped in the US
Thanks!
- Fri Feb 16, 2018 8:31 pm
- Forum: Looking to Buy
- Topic: WTB mintyPi 2.0
- Replies: 8
- Views: 4889
Re: WTB mintyPi 2.0
I just posted mine on the For Sale page.