Search found 92 matches

by Dividion
Wed Feb 24, 2021 10:47 am
Forum: General Project Chat
Topic: Raspberry pi zero gameboy cartridge.
Replies: 2
Views: 104

Re: Raspberry pi zero gameboy cartridge.

Sounds like you might be better off with just an Everdrive cartridge. If you want to play other systems and use the Pi's GPIO to communicate through the GB cartridge connector so that it looks like a GB cartridge... that's an awfully ambitious undertaking. It'd be pretty awesome, especially since it...
by Dividion
Mon Feb 15, 2021 10:55 pm
Forum: General Hardware
Topic: Cutting Helders RetroPSU to make it a little smaller?
Replies: 2
Views: 199

Re: Cutting Helders RetroPSU to make it a little smaller?

Only @Helder can answer for sure. Did you message him? I'd guess that two of those resistors go with the LEDs, but I'm not sure what the other resistor and capacitor are for.
by Dividion
Fri Feb 12, 2021 6:33 pm
Forum: General Hardware
Topic: ili9341 SPI TFT Screen Connectors (for bare screens without boards)
Replies: 43
Views: 25343

Re: ili9341 SPI TFT Screen Connectors (for bare screens without boards)

Wow. Are you Broomhill? That EXACT same question was asked (and answered) on page 2, years ago. I see 8 connections on the board but Moosepr's guide shows there are 9. Specifically, how is the connection for BL to pin12 accounted for? I'm a bit confused, I see 8 connections on the board but Moosepr'...
by Dividion
Sat Feb 06, 2021 3:08 pm
Forum: General Chat (Game Boy Zero)
Topic: Can you make the button pcb from scratch??
Replies: 2
Views: 159

Re: Can you make the button pcb from scratch??

Yeah, you can find GBZ common ground button boards just about anywhere: My site: http://pocketadventures.com Ebay: https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2380057.m570.l1313&_nkw=game+boy+zero+pcb&_sacat=0 Aliexpress: https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_202102061...
by Dividion
Fri Feb 05, 2021 11:13 pm
Forum: Show-off Corner (3d Printing)
Topic: Wireless 3d Printing - Cheap - The Orange Pi Zero and OctoPrint
Replies: 1
Views: 2396

Re: Wireless 3d Printing - Cheap - The Orange Pi Zero and OctoPrint

FYI... The images don't seem to load anymore. Apparently it doesn't like mixing secure and non-secure content. If they don't show up for you, and your browser doesn't give you the option to load them anyway, you can right-click them and open in a new tab.
by Dividion
Sun Jan 31, 2021 7:30 pm
Forum: General Chat (mintyPi)
Topic: atari 2600 games
Replies: 5
Views: 551

Re: atari 2600 games

Atari emulators for the pi zero suck, I can't get them to run on the stock emulator. I used their alternative which loaded the roms but no way to fix the controls as I believe they are hard coded and are not a Libretro core. So as far as I can see the problem is the emulator and it's not a mintyPi ...
by Dividion
Fri Jan 29, 2021 2:56 pm
Forum: General Chat (Game Boy Zero)
Topic: Is there 3d model of x/y buttons?
Replies: 4
Views: 215

Re: Is there 3d model of x/y buttons?

Yeah, those aren't that common. I think most users wanting to differentiate all the buttons use the red/yellow/green/blue super famicom theme. There are some on Thingiverse. The quality will really depend on your printer and whether you mind doing some sanding to improve them: https://www.thingivers...
by Dividion
Wed Sep 30, 2020 10:19 am
Forum: Support for Kite's Products
Topic: Super AIO - Updating to latest Retropie image?
Replies: 23
Views: 4973

Re: Super AIO - Updating to latest Retropie image?

Well - I used the Raspberry Pi imager to go to 4.4 to try and fix my issues from thread https://www.sudomod.com/forum/viewtopic.php?f=51&t=10424. It booted once, then I turned off and thought safe shutdown ran. Then I turned it back on and it went through the scan disk procedure. It asked me to pre...
by Dividion
Tue Sep 29, 2020 3:09 pm
Forum: General Chat (Game Boy Zero)
Topic: Game Boy Zero folks: do your GBZ's actually work on SNES?
Replies: 3
Views: 870

Re: Game Boy Zero folks: do your GBZ's actually work on SNES?

From my experience, GBA and SNES are essentially the limit of what the Pi Zero can handle. For the GBA, the lr-mgba emulator tends to stutter, but I've had good gameplay experiences using the lr-gpsp emulator. For SNES I think I've always used the default (lr-snes9x I think) and can't recall any pro...
by Dividion
Tue Sep 15, 2020 11:44 pm
Forum: General Project Chat
Topic: Need help for repair Game hat wavrshare
Replies: 2
Views: 785

Re: Need help for repair Game hat wavrshare

Looks like it was probably an MT3608, given its proximity to an FS8205 and 22uH inductor, but I'm not sure if that can be easily salvaged. Maybe once it's cleaned up. https://lcsc.com/product-detail/DC-DC-Converters_MT3608_C84817.html Disclaimer: I don't own one, so I can't be sure if that's what it...