Search found 2985 matches
- Sat Feb 20, 2021 6:55 pm
- Forum: General Chat (mintyPi)
- Topic: atari 2600 games
- Replies: 5
- Views: 11303
Re: atari 2600 games
Atari emulators for the pi zero suck, I can't get them to run on the stock emulator. I used their alternative which loaded the roms but no way to fix the controls as I believe they are hard coded and are not a Libretro core. So as far as I can see the problem is the emulator and it's not a mintyPi ...
- Sun Jan 31, 2021 10:15 am
- Forum: Support (mintyPi)
- Topic: Mntypi V3 Shutdown Error
- Replies: 1
- Views: 5918
Re: Mntypi V3 Shutdown Error
Looks like you have the Hall Sensor shorted, very likely the GPIO is shorted to one of it's neighboring GPIO.
- Sun Jan 31, 2021 10:07 am
- Forum: General Chat (mintyPi)
- Topic: Searching for a Screen/ Display
- Replies: 3
- Views: 7403
Re: Searching for a Screen/ Display
Hi, I’m trying to build my own mintyPi without purchasing Helder’s parts for $90, and I’m not managing to find a reasonable screen. I’m not adding a speaker, so the screen could be up to 3.2 inches. Anything I find either has a GPIO connector at the back or works with a ribbon cable that’s too thic...
- Sun Jan 31, 2021 10:01 am
- Forum: General Chat (mintyPi)
- Topic: atari 2600 games
- Replies: 5
- Views: 11303
Re: atari 2600 games
Atari emulators for the pi zero suck, I can't get them to run on the stock emulator. I used their alternative which loaded the roms but no way to fix the controls as I believe they are hard coded and are not a Libretro core. So as far as I can see the problem is the emulator and it's not a mintyPi o...
- Tue Jan 05, 2021 7:57 pm
- Forum: Support (mintyPi)
- Topic: Possible solder issue with audio
- Replies: 4
- Views: 7639
Re: Possible solder issue with audio
That 3rd pin is a GND so if it was bridged it would no even start up. There is no sound unless you have a game to actually load so more than likely sound works but if you enter a menu like say the Show IP in the Retropie Menu it will cause a pop noise from the speaker so if you hear that then you ha...
- Tue Jan 05, 2021 6:24 pm
- Forum: Support (mintyPi)
- Topic: ### V3.5 White Screen Fix ####
- Replies: 0
- Views: 18631
### V3.5 White Screen Fix ####
If you are getting a white screen and your soldering is good (bad or questionable soldering is not going to fix a white screen) you will need to use the latest image that fixes white screens happening. Burn it to the SD and insert into the Pi and you should be good to go. https://www.mediafire.com/...
- Tue Jan 05, 2021 6:18 pm
- Forum: Support (mintyPi)
- Topic: MintyPI Boots and works on micro USB, but on USB-C and Battery Turns off
- Replies: 1
- Views: 5479
Re: MintyPI Boots and works on micro USB, but on USB-C and Battery Turns off
Test the TX pin when powered through microUSB , measure the voltage there and if it is 0 then you either shorted the pin or Electro Static Discharge could have damaged the GPIO. This GPIO is crucial in keeping the pi on and also turning it off and if it is damaged then you will need another Raspberr...
- Tue Jan 05, 2021 6:06 pm
- Forum: Support (mintyPi)
- Topic: MintyPi 3.5 Screen Issue
- Replies: 2
- Views: 6370
Re: MintyPi 3.5 Screen Issue
There is a new Image out that was released 2 days after the initial release that you likely are using that fixes the issue.
https://www.mediafire.com/file/skv96iou ... 0.rar/file
https://www.mediafire.com/file/skv96iou ... 0.rar/file
- Sat Oct 31, 2020 5:33 pm
- Forum: Support (mintyPi)
- Topic: mintypi v3 power board
- Replies: 2
- Views: 6814
Re: mintypi v3 power board
Sounds like the battery is not fully charged or might not be seated properly, measure the battery voltage at the battery and the 3d pin from the top on the white connector when you press the power button. https://cdn.discordapp.com/attachments/197017091352690688/608006048124633088/20190805_143217.jpg
- Sat Oct 31, 2020 5:29 pm
- Forum: Support (mintyPi)
- Topic: Mintypi V2 bridged solder point help
- Replies: 1
- Views: 5880
Re: Mintypi V2 bridged solder point help
Use solder braid with a soldering iron tip that is larger than the one you are using to solder the pi to the pcb.