Search found 114 matches

by goodBEan
Sun Mar 04, 2018 2:40 pm
Forum: Design Sharing (3d Printing)
Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
Replies: 70
Views: 20198

Re: [WIP] Tact-4 shoulder button bracket

So here is what came out next.
On the left, the drill guide. Right, final mount. Right now Its only theory, so don't drill anything.
Image

current files
https://www.dropbox.com/s/aefnx8gn8cipt ... 0.zip?dl=0
by goodBEan
Sat Mar 03, 2018 3:16 pm
Forum: Design Sharing (3d Printing)
Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
Replies: 70
Views: 20198

Re: [WIP] Tact-4 shoulder button bracket

So did some test prints and I am I a few more things to do. Since I do have a clear case It makes it easier to see where the buttons would end up. So far it looks like having them go straight down and bit space out is the way to go. https://i.imgur.com/8pjDmx0.jpg However the way it sits now even my...
by goodBEan
Thu Mar 01, 2018 8:44 pm
Forum: Design Sharing (3d Printing)
Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
Replies: 70
Views: 20198

Re: [WIP] Tact-4 shoulder button bracket

Now that I got the fit to the gameboy correct. Now I need to get to the fit to the tact switches going. From one my earlier versions it wasn't an issue. Luckly I still have the place holders to work from. https://i.imgur.com/pykhpvr.png https://i.imgur.com/cRn5N6Q.png https://i.imgur.com/vBnWyfw.png...
by goodBEan
Wed Feb 28, 2018 11:42 am
Forum: Design Sharing (3d Printing)
Topic: [UPDATE] "Air duct" and "fan-mount" for kites circuit sword
Replies: 46
Views: 13421

Re: [WIP] Fan/blower mount for kites circuit sword

Not thrilled about re soldering the fan. All these brackets look incredible.

Honestly I didn't notice any interference between the parts.
by goodBEan
Tue Feb 27, 2018 9:16 pm
Forum: Support for Kite's Products
Topic: CSO adding lights
Replies: 1
Views: 454

CSO adding lights

I know I asked this before on the big pre-order thread and I cannot remember the answer or find it. So I have to ask it again. I am considering adding some leds to my GBZ since its in a clear case. I know that it was recommended that I solder it into a test pad so that I can turn it on or off with a...
by goodBEan
Sun Feb 25, 2018 8:30 am
Forum: Design Sharing (3d Printing)
Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
Replies: 70
Views: 20198

Re: [WIP] Tact-4 shoulder button bracket

Made adjustments with hoolyhoos switch bracket. Essentially the way I approached it was to import the part into blender, and make the one section of it bigger, and extend it down so that I could have the wiggle room. NEW LINK https://www.dropbox.com/s/c09xo2y1cgdzxcg/sholderbutton%20bracket-v8blank....
by goodBEan
Sat Feb 24, 2018 5:57 pm
Forum: Show-off Corner (3d Printing)
Topic: I'm excited...the wife, not so much.
Replies: 6
Views: 3580

Re: I'm excited...the wife, not so much.

Print your wife a swan, wives loves swans https://www.thingiverse.com/thing:731686
by goodBEan
Sat Feb 24, 2018 5:01 pm
Forum: Design Sharing (3d Printing)
Topic: Glue Less Support Bracket for Kite's Mode/Power Switch Board
Replies: 44
Views: 17236

Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board

Hoolyhoo, Looks like its nothing major. Gray part is mine and they are close, i can make some adjustments.
Image
by goodBEan
Sat Feb 24, 2018 3:57 pm
Forum: Design Sharing (3d Printing)
Topic: Glue Less Support Bracket for Kite's Mode/Power Switch Board
Replies: 44
Views: 17236

Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board

Oh wow, maybe you can combine your design with mine and make one piece for that side. Just a thought. :) Maybe a combo part won't be necessary. I want mine to work no mater what switch or other parts are in play. I could just make adjustments to mine or just a variant to get mine out of the way. I ...
by goodBEan
Sat Feb 24, 2018 3:31 pm
Forum: Design Sharing (3d Printing)
Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
Replies: 70
Views: 20198

Re: [WIP] Tact-4 shoulder button bracket

My last few print's have not been 100 a snug fit but recent adjustements made it damn closer. https://i.imgur.com/hXje34H.jpg My next version has to make some room for two sets of tact switches. https://i.imgur.com/zSQSKJE.jpg Right before I decided to finish for the day I found a bracket made by ho...