Search found 75 matches

by Dividion
Thu May 28, 2020 8:27 am
Forum: Show-off Corner (Game Boy Zero)
Topic: Build Log: First Time Builder
Replies: 9
Views: 155

Re: Build Log: First Time Builder

if you're doing a an actual teensy, your best bet is to follow wermy's guide. if i recall correctly, it can be tricky getting the arduino ide to work with it. tinkerboy's guide uses a pro micro so i'm not sure it'll work on a teensy. the buttons are already mapped in his code sample. Actually, it s...
by Dividion
Wed May 27, 2020 9:31 pm
Forum: General Chat (Game Boy Zero)
Topic: Pocketadventures.com is this site legit?
Replies: 3
Views: 62

Re: Pocketadventures.com is this site legit?

I hope my site's legit! :)

Valid question though. Let me know if you have any questions about any of the products.
by Dividion
Wed May 27, 2020 8:21 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: Build Log: First Time Builder
Replies: 9
Views: 155

Re: Build Log: First Time Builder

In the meantime, I'm thinking of setting up the pi zero ready for the build. I'm guessing I will need to configure the controller part of retropie to match the keyboard strokes the pi teensy will be configured with. I am going to use Wermy's teensy programing. Does anyone know where I can find the ...
by Dividion
Sat May 23, 2020 10:22 am
Forum: Show-off Corner
Topic: Custom 4.3in Landscape Handheld w/ GameBoy Advance SP-style Buttons
Replies: 3
Views: 206

Custom 4.3in Landscape Handheld w/ GameBoy Advance SP-style Buttons

This project was something I've wanted to do for awhile and I was finally able to get around to it. I've always liked the soft-clicky feel of the GameBoy Advance SP's buttons. I also wanted to use up a bunch of extra components I've accumulated over the past couple of years, including some 4.3in com...
by Dividion
Fri May 22, 2020 8:00 am
Forum: Hardware Help
Topic: Modding a 5" lcd to 5V?
Replies: 4
Views: 239

Re: Modding a 5" lcd to 5V?

Did you check the composite screens list to see if the controller board has a known 5V mod? https://www.sudomod.com/wiki/index.php/GBZ_Screen Otherwise, if you have a voltmeter, you could carefully check the pins of any 8-pin chips on the board to see if it's 5V. Usually it's one of the middle pins,...
by Dividion
Thu May 21, 2020 6:00 am
Forum: Support (Game Boy Zero)
Topic: Gameboy DMG Screws Query
Replies: 3
Views: 106

Re: Gameboy DMG Screws Query

The only difference between m2 6mm and m2 8mm is that the one is 2mm longer than the other. If it's not wide enough to grip properly, you probably need m2.5 or m3.
by Dividion
Sat May 02, 2020 6:46 pm
Forum: General Chat (Game Boy Zero)
Topic: Very New Questions
Replies: 9
Views: 769

Re: Very New Questions

Just got caught up on this thread. Thanks for all the mentions, @infinitLoop! @kschmidt0303 Using a composite screen is definitely the easiest way to go, as it only requires 3 wires: +5v, GND and signal. With most composite screens pulled from backup cameras, you need to modify them to use 5V instea...
by Dividion
Mon Apr 20, 2020 10:57 am
Forum: Show-off Corner (Game Boy Zero)
Topic: GameBoy RR (Rolls Royce)
Replies: 6
Views: 696

Re: GameBoy RR (Rolls Royce)

Just got my shell from Boxy Pixel last Friday. A little heavier than I expected, but looks amazing. Still waiting on the 640x480 screen and then I'll piece it together.
by Dividion
Sun Mar 29, 2020 8:54 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: Aluminum Case
Replies: 17
Views: 2359

Re: Aluminum Case

Final picture showing back buttons. This was perhaps the easiest build to put together. Everything just screws together and the only place I put hot-glue was to hold the speaker in place. It looks like there's going to be something to hold the speaker in place, but I didn't receive that with my pur...