Search found 81 matches

by Dividion
Sun Aug 19, 2018 5:48 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: Rodocop's 15th GBZ
Replies: 17
Views: 4946

Re: Rodocop's 15th GBZ

It looks really slick, Rodocop.

Do you know if those water slide decals show up on a black case? (assuming you print in non-black ink that is) Or would it be like printing in color on a sheet of black paper?
by Dividion
Sun Aug 19, 2018 5:41 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: My New PCB Prototypes
Replies: 81
Views: 19662

Re: My New PCB Prototypes

Awesome work ! The picture of all the boards looks super neat, let us know how it all goes for you Thanks! Version 1.0 of the button boards (black and red) should be delivered tomorrow, as well as a new SPI adapter, PWM audio filter, headphone jack breakout board, and a new prototype for the GPIO A...
by Dividion
Fri Aug 17, 2018 7:41 pm
Forum: Support (mintyPi)
Topic: [SOLVED] On-screen battery won't display
Replies: 2
Views: 1868

Re: On-screen battery won't display

Manually running the pngview program I could get it to display, so I started running back through the MintyInstall.sh commands manually. Looks like the following command is what failed: sudo pip install adafruit-ads1x15 So it wasn't seeing the ADS1015 correctly. After I re-ran that command, it start...
by Dividion
Thu Aug 16, 2018 7:06 pm
Forum: Support (mintyPi)
Topic: [SOLVED] On-screen battery won't display
Replies: 2
Views: 1868

[SOLVED] On-screen battery won't display

Hi all, I set up the Mintybatterymonitor on my GBZ running 4.3 no problem. Wired a button to the GPIO and set it so when_held for 2 seconds it shuts down, and when_released (short press) it toggles the on-screen battery. I just installed the battery monitor on a new device running 4.4, and it wasn't...
by Dividion
Mon Aug 13, 2018 6:25 am
Forum: Support (Game Boy Zero)
Topic: Targus usb hub change?
Replies: 2
Views: 512

Re: Targus usb hub change?

Red, Green and White would still be the same. You'd probably use "B" for the Black, since it's clearly going to ground (the large copper area of the board rather than the skinny trace lines). But "S" is also clearly grounded (and it's also black). If they're coming from a regular USB2 connector, the...
by Dividion
Sun Aug 12, 2018 10:41 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: Another completed Circuit Sword GB
Replies: 3
Views: 1432

Re: Another completed Circuit Sword GB

I really like the color combination of those buttons. Personally I'd be really happy with those results also. Well done!
by Dividion
Mon Aug 06, 2018 1:30 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: My New PCB Prototypes
Replies: 81
Views: 19662

Re: My New PCB Prototypes

My delicious new prototype boards arrived today. Woohoo!
Image

Image

Image
by Dividion
Sun Aug 05, 2018 7:56 pm
Forum: Support (Game Boy Zero)
Topic: Checking in progress on 1 disk
Replies: 10
Views: 5968

Re: Checking in progress on 1 disk

I've had that same issue with 4.4 on the zero, but not with 4.3 or 4.4 on the Pi3. Thanks for a clean solution.
by Dividion
Thu Aug 02, 2018 6:02 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: My New PCB Prototypes
Replies: 81
Views: 19662

Re: My New PCB Prototypes

Yeah, that was with the CM102S+ hooked up, and the logitech receiver connected as well. I've got a bunch of Pro Micro modules, and a couple Tinkerboy boards I still need to use that have the Pro Micros also, so I'll get some good testing in when I connect those. Given that Tinkerboy's new AIOs basic...
by Dividion
Thu Aug 02, 2018 4:09 pm
Forum: Show-off Corner (Game Boy Zero)
Topic: My New PCB Prototypes
Replies: 81
Views: 19662

Re: My New PCB Prototypes

Yes on the full data speeds but some devices like some keyboards (logitech always works it seems) and some usb wifi cards and usb flash drives often are not recognized. When you have the CM102S+ hooked up and you use a USB Drive does it recognize on the Pi? If so then you might be ok. The two Kings...