Search found 972 matches
- Fri Jan 12, 2018 8:01 am
- Forum: Support for Kite's Products
- Topic: [Solved] My SAIO won't boot
- Replies: 3
- Views: 3244
Re: My SAIO won't boot
That is, really strange! Was something plugged in to USB when it was dropped? Did it fall apart when dropped? Your next step should be to take it apart and look around the back board first. Using a multimeter, make sure that when the power switch is 'on' that there is continuity between GND and the ...
- Fri Jan 12, 2018 6:46 am
- Forum: Support for Kite's Products
- Topic: [Solved] White Colors appear blue
- Replies: 4
- Views: 3681
Re: White Colors appear blue
Good work could you please put "[solved] in the title of your post
- Thu Jan 11, 2018 6:20 am
- Forum: Support for Kite's Products
- Topic: [solved] Sound goes from stereo to mono
- Replies: 9
- Views: 6017
Re: Sound goes from stereo to mono
Yep they are the same, my fault it should have been B103 which is a 10k pot! Double check soldering, and try replace once more.. other than that i'm not entirely sure what it could be!
- Thu Jan 11, 2018 4:57 am
- Forum: Support for Kite's Products
- Topic: [solved] Sound goes from stereo to mono
- Replies: 9
- Views: 6017
Re: Sound goes from stereo to mono
Possibly? Was it a 10k pot you used? how do I know that? It looks the same like yours. On the bottom if it says something like B10K, then it's 10k ... i think there are also B50K and maybe B100K? Which was 50k and 100k respectively .. ALL should work, as always at 0% on the pot, the wiper should be...
- Thu Jan 11, 2018 1:42 am
- Forum: Support for Kite's Products
- Topic: [Solved] White Colors appear blue
- Replies: 4
- Views: 3681
Re: White Colors appear blue
Hi, put it onto the 'tester mode' and get a picture of the colour bars when it's in the 'bad state' and I can point out which pins you need to solder, but basically it is a soldering thing (dry joint between Pi and SAIO) which will be one of these pins: https://github.com/geebles/Super-AIO/wiki/Trou...
- Wed Jan 10, 2018 3:01 pm
- Forum: Support for Kite's Products
- Topic: [solved] Sound goes from stereo to mono
- Replies: 9
- Views: 6017
Re: Sound goes from stereo to mono
Possibly? Was it a 10k pot you used?
Perhaps it got damaged by heat? Or perhaps the pot is designed differently? When turned all the way down the output is basically shorted to gnd.. you could try lowering the volume in Linux a bit lower? Or replace pot again! Haha..
Perhaps it got damaged by heat? Or perhaps the pot is designed differently? When turned all the way down the output is basically shorted to gnd.. you could try lowering the volume in Linux a bit lower? Or replace pot again! Haha..
- Wed Jan 10, 2018 2:58 pm
- Forum: Support for Kite's Products
- Topic: Video Out of GBZ on Kite's Board
- Replies: 17
- Views: 11499
Re: Video Out
Nope those are the speaker outputs and cannot be used for headphones..
I'm referring to the legs of the 3.5mm audio jack, you can see on that image to the left of the speaker is the 3.5mm jack.. it has 5 solder points, I'll show you tomorrow which ones you need to use
I'm referring to the legs of the 3.5mm audio jack, you can see on that image to the left of the speaker is the 3.5mm jack.. it has 5 solder points, I'll show you tomorrow which ones you need to use
- Wed Jan 10, 2018 2:32 am
- Forum: Support for Kite's Products
- Topic: [solved] Sound goes from stereo to mono
- Replies: 9
- Views: 6017
Re: Sound goes from stereo to mono
It is most likely the volume pot itself because it is a stereo pot (it's basically 2x linear pots in the same package) and they aren't really proper audio grade ones (not sure you can get them this small) so they are probably misaligned internally.. The real way to fix is probably to replace the pot...
- Tue Jan 09, 2018 9:00 am
- Forum: Support for Kite's Products
- Topic: Read before posting
- Replies: 4
- Views: 29573
Re: Read before posting
Just adding that the PDF guide is a bit out dated, so always start with the wiki:
https://github.com/geebles/Super-AIO/wi ... ng-Started
https://github.com/geebles/Super-AIO/wi ... ng-Started
- Tue Jan 09, 2018 4:54 am
- Forum: Guides
- Topic: [GUIDE][SOURCE] Retropie SUPER OSD
- Replies: 6
- Views: 29975
Re: [GUIDE][SOURCE] SUPER OSD
Since a huge amount of your code was not available I think that my work simply comes from good coding and best practices ;) , moreover I don't even see any lock mechanics in your code such those I used to increase the polling efficiency in the python part. I coded this in a couple of days, feel fre...