Page 4 of 4

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Fri Jun 09, 2017 12:34 pm
by Fixmylife
How would you get the audio from the hdmi to also work with this set up

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Fri Jul 14, 2017 5:29 pm
by ICMF
Kilren wrote:
Fri Jun 10, 2016 1:24 pm
Image
(The audio jack isn't exactly the same pin layout as the radioshack one, so if confused, refer to my picture in the breadboard section.

This is probably a dumb question, but... can I pull the 5V for the Amp from the USB on the DAC, or would that cause problems? In other words, do I need a separate 5V connection from the amp, or can I wire it in-line with the DAC?

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Sat Jul 15, 2017 2:11 am
by ABH
ICMF wrote:
Fri Jul 14, 2017 5:29 pm
Kilren wrote:
Fri Jun 10, 2016 1:24 pm
Image
(The audio jack isn't exactly the same pin layout as the radioshack one, so if confused, refer to my picture in the breadboard section.

This is probably a dumb question, but... can I pull the 5V for the Amp from the USB on the DAC, or would that cause problems? In other words, do I need a separate 5V connection from the amp, or can I wire it in-line with the DAC?
I pull the 5V for the Amp from the USB DAC
working great

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Sat Jul 22, 2017 10:35 pm
by firestw152
Healy_um wrote:
Tue May 16, 2017 9:43 am
So I've followed this tutorial and I can get sound out of the jack, but nothing comes through the speaker. I've double and tripple checked my wiring and its all good. Not sure what other info to give, but ask away if you need. Any help will be great! Thanks :)
Did you ever find a solution?

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Thu Sep 21, 2017 9:07 pm
by fsatatkid
I know this thread is old and this question probably won't be heard, but I had a (maybe) dumb question. I'm trying to use the sabrant DAC with the adafruit amp wermy used in his build. In the diagram shown in this thread there are three wires coming from the DAC to the amp; L,R, and what looks like an upside down T. What is that middle (green) wire for? The adafruit amp only has two audio in channels alongside the power and ground (and a shutdown pin).

Can anyone clarify?

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Fri Sep 22, 2017 1:27 am
by vnman
The upside down "T" is ground. There is no need to connect this to ground, just leave it unconnected.

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Thu Oct 04, 2018 9:26 pm
by djczer
So, I didn't use my adafruit mono amp since I use the USB Audio Card. Is there a still a need for the audio amp? I used the DAC. Just curious if anyone has a wiring up of all this using the original headphone jack? I tried to follow Wormy layout but the DAC has stereo so I made use of that.

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Fri Oct 05, 2018 1:11 am
by KonnorJ
In some cases you won't need an amp you'll have to wire it up and see though.

Re: Non-OEM Audio Guide - No DMG Parts

Posted: Sun Nov 04, 2018 10:33 pm
by Jdrkangl2
If you don't use a usb hub then how do you wire this directly to the Pi? The usb part I mean