Page 5 of 59

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Fri Mar 10, 2017 1:50 pm
by HoolyHoo
DarrylUK wrote:I've tried a couple of prints now at work. We print pretty regularly so this shouldn't be a rookie mistake.

The 2 square cut outs in the button weeks look like they should have 1 layer thick to stop the buttons pushing through the bracket, is that correct? I'm not getting enough material in that area for some reason, essentially the button can pass through the bracket. Any recommendations?
Yes, that is correct. Originally I did not have that at all but buttons were sitting too high up and not level with A and B buttons. I made it .2mm thick, just enough for one layer. Are you using .2mm layer height? What slicer are you using?

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Fri Mar 10, 2017 1:57 pm
by DarrylUK
HoolyHoo wrote:
DarrylUK wrote:I've tried a couple of prints now at work. We print pretty regularly so this shouldn't be a rookie mistake.

The 2 square cut outs in the button weeks look like they should have 1 layer thick to stop the buttons pushing through the bracket, is that correct? I'm not getting enough material in that area for some reason, essentially the button can pass through the bracket. Any recommendations?
Yes, that is correct. Originally I did not have that at all but buttons were sitting too high up and not level with A and B buttons. I made it .2mm thick, just enough for one layer. Are you using .2mm layer height? What slicer are you using?
I'll check, I actually got one of my engineers to print it. We're actually due a new 3D printer next week so I might give it a try on that.

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Fri Mar 10, 2017 2:00 pm
by HoolyHoo
DarrylUK wrote:
HoolyHoo wrote:
DarrylUK wrote:I've tried a couple of prints now at work. We print pretty regularly so this shouldn't be a rookie mistake.

The 2 square cut outs in the button weeks look like they should have 1 layer thick to stop the buttons pushing through the bracket, is that correct? I'm not getting enough material in that area for some reason, essentially the button can pass through the bracket. Any recommendations?
Yes, that is correct. Originally I did not have that at all but buttons were sitting too high up and not level with A and B buttons. I made it .2mm thick, just enough for one layer. Are you using .2mm layer height? What slicer are you using?
I'll check, I actually got one of my engineers to print it. We're actually due a new 3D printer next week so I might give it a try on that.
Layer One:
Layer1.png
Layer1.png (661.89 KiB) Viewed 6217 times
Layer Two:
Layer2.png
Layer2.png (739.6 KiB) Viewed 6217 times

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Sat Mar 11, 2017 7:09 am
by mwx
I just printed mine, thanks again for this model!

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Mon Mar 13, 2017 4:08 am
by Mynasru
HoolyHoo wrote:
DarrylUK wrote:I've tried a couple of prints now at work. We print pretty regularly so this shouldn't be a rookie mistake.

The 2 square cut outs in the button weeks look like they should have 1 layer thick to stop the buttons pushing through the bracket, is that correct? I'm not getting enough material in that area for some reason, essentially the button can pass through the bracket. Any recommendations?
Yes, that is correct. Originally I did not have that at all but buttons were sitting too high up and not level with A and B buttons. I made it .2mm thick, just enough for one layer. Are you using .2mm layer height? What slicer are you using?
I can not get the same layer one, I'm using the cura clicer in Repetier host :/

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Mon Mar 13, 2017 4:31 am
by tralalem
I glued the screen in the housing yesterday with the bracket without buttons. The status LEDs of the Kite Super AiO do not fit and I had to cut away some plastic. Does anybody experience the same issue?

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Mon Mar 13, 2017 4:38 am
by HoolyHoo
Mynasru wrote:
HoolyHoo wrote:
DarrylUK wrote:I've tried a couple of prints now at work. We print pretty regularly so this shouldn't be a rookie mistake.

The 2 square cut outs in the button weeks look like they should have 1 layer thick to stop the buttons pushing through the bracket, is that correct? I'm not getting enough material in that area for some reason, essentially the button can pass through the bracket. Any recommendations?
Yes, that is correct. Originally I did not have that at all but buttons were sitting too high up and not level with A and B buttons. I made it .2mm thick, just enough for one layer. Are you using .2mm layer height? What slicer are you using?
I can not get the same layer one, I'm using the cura clicer in Repetier host :/
I do no use cura but try setting your bottom layer height to .2mm.

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Mon Mar 13, 2017 5:23 am
by HoolyHoo
tralalem wrote:I glued the screen in the housing yesterday with the bracket without buttons. The status LEDs of the Kite Super AiO do not fit and I had to cut away some plastic. Does anybody experience the same issue?
How did you solder your LED's? If you soldered through the top (the side with Kites logo) and not the bottom or through hole then there should be no modification necessary to bracket. Otherwise some cutting might be required.

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Mon Mar 13, 2017 6:07 am
by tralalem
HoolyHoo wrote:
tralalem wrote:I glued the screen in the housing yesterday with the bracket without buttons. The status LEDs of the Kite Super AiO do not fit and I had to cut away some plastic. Does anybody experience the same issue?
How did you solder your LED's? If you soldered through the top (the side with Kites logo) and not the bottom or through hole then there should be no modification necessary to bracket. Otherwise some cutting might be required.
I soldered the LEDs like in KITE guide, they are too low and touching the plastic of the frame, even with a bit removed they are still touching the LCD I think. I will try to remove them and solder them to be at the other side of the board.
Image

Re: HoolyHoo's AIO bracket for Kite's SAIO Board

Posted: Mon Mar 13, 2017 6:12 am
by HoolyHoo
tralalem wrote:
HoolyHoo wrote:
tralalem wrote:I glued the screen in the housing yesterday with the bracket without buttons. The status LEDs of the Kite Super AiO do not fit and I had to cut away some plastic. Does anybody experience the same issue?
How did you solder your LED's? If you soldered through the top (the side with Kites logo) and not the bottom or through hole then there should be no modification necessary to bracket. Otherwise some cutting might be required.
I soldered the LEDs like in KITE guide, they are too low and touching the plastic of the frame, even with a bit removed they are still touching the LCD I think. I will try to remove them and solder them to be at the other side of the board.
Image
If you solder them on top with the legs straight and sitting on top of the board, you should be fine.