[FOR SALE] Picicle a portable games console

Sell or trade things with other forum members!
User avatar
rodocop
Posts: 1723
Joined: Mon Aug 22, 2016 3:14 pm
Location: Saskatchewan
Has thanked: 606 times
Been thanked: 608 times

Re: [FOR SALE] Picicle a portable games console

Post by rodocop » Sat May 25, 2019 8:46 am

Picicle wrote:
Sat May 25, 2019 8:32 am
rodocop wrote:
Sat May 25, 2019 8:26 am
I did reflash and it fixed the putty issues. I will check all those points you have show and report back later today.
OK
So at the 3.3v and 3v pin I am only getting around .864v on both.

User avatar
Picicle
Posts: 68
Joined: Wed Apr 24, 2019 2:08 pm
Has thanked: 6 times
Been thanked: 20 times

Re: [FOR SALE] Picicle a portable games console

Post by Picicle » Sat May 25, 2019 8:51 am

rodocop wrote:
Sat May 25, 2019 8:46 am


So at the 3.3v and 3v pin I am only getting around .864v on both.
Pin 1 GPIO of Raspberry 3.3V?

User avatar
rodocop
Posts: 1723
Joined: Mon Aug 22, 2016 3:14 pm
Location: Saskatchewan
Has thanked: 606 times
Been thanked: 608 times

Re: [FOR SALE] Picicle a portable games console

Post by rodocop » Sat May 25, 2019 9:16 am

Picicle wrote:
Sat May 25, 2019 8:51 am
rodocop wrote:
Sat May 25, 2019 8:46 am


So at the 3.3v and 3v pin I am only getting around .864v on both.
Pin 1 GPIO of Raspberry 3.3V?
Gpio1 reading ~3.2v.

User avatar
Picicle
Posts: 68
Joined: Wed Apr 24, 2019 2:08 pm
Has thanked: 6 times
Been thanked: 20 times

Re: [FOR SALE] Picicle a portable games console

Post by Picicle » Sat May 25, 2019 9:34 am

rodocop wrote:
Sat May 25, 2019 9:16 am


Gpio1 reading ~3.2v.
GPIO 1 wired up to pin 9 of screen. No soldering?

User avatar
rodocop
Posts: 1723
Joined: Mon Aug 22, 2016 3:14 pm
Location: Saskatchewan
Has thanked: 606 times
Been thanked: 608 times

Re: [FOR SALE] Picicle a portable games console

Post by rodocop » Sat May 25, 2019 9:55 am

Gpio 1 should have continuity with pin 9 on screen? I will double check continuity, and add more solder to gpio1

User avatar
Picicle
Posts: 68
Joined: Wed Apr 24, 2019 2:08 pm
Has thanked: 6 times
Been thanked: 20 times

Re: [FOR SALE] Picicle a portable games console

Post by Picicle » Sat May 25, 2019 9:58 am

rodocop wrote:
Sat May 25, 2019 9:55 am
Gpio 1 should have continuity with pin 9 on screen?
Yes.

If you want, I can send a PCB circuit.

User avatar
rodocop
Posts: 1723
Joined: Mon Aug 22, 2016 3:14 pm
Location: Saskatchewan
Has thanked: 606 times
Been thanked: 608 times

Re: [FOR SALE] Picicle a portable games console

Post by rodocop » Sat May 25, 2019 10:07 am

Picicle wrote:
Sat May 25, 2019 9:58 am
rodocop wrote:
Sat May 25, 2019 9:55 am
Gpio 1 should have continuity with pin 9 on screen?
Yes.

If you want, I can send a PCB circuit.
Sure.

Just checked and there is no continuity from gpio1 to pin 9. Likely just need to add more solder for a better connection. I did not realize the screen took power from pin1

User avatar
rodocop
Posts: 1723
Joined: Mon Aug 22, 2016 3:14 pm
Location: Saskatchewan
Has thanked: 606 times
Been thanked: 608 times

Re: [FOR SALE] Picicle a portable games console

Post by rodocop » Sat May 25, 2019 8:24 pm

Well the screen issue is solved, it was in fact that the pi's 3.3v gpio was not soldered well enough, so it wasn't making a good connection. Fixed that, now the screen works.....But now, the pi will freeze after about 5 -10 minutes use (just sitting, not playing any games). I'll re flash again, and see if that helps...

EDIT, well even a new card freezes, and it's more like 2 minutes, before it freezes, I guess i'll open it up one more time and re check all the power connections on the pi....

User avatar
Picicle
Posts: 68
Joined: Wed Apr 24, 2019 2:08 pm
Has thanked: 6 times
Been thanked: 20 times

Re: [FOR SALE] Picicle a portable games console

Post by Picicle » Sun May 26, 2019 5:15 am

rodocop wrote:
Sat May 25, 2019 8:24 pm

EDIT, well even a new card freezes, and it's more like 2 minutes, before it freezes, I guess i'll open it up one more time and re check all the power connections on the pi....
Perhaps the problem is in the video settings. When i did img, I set the maximum speed for my Pi. But all Raspberry are different. Try in file /etc/modprobe.d/fbtft.conf reduce speed to 60 000 000.

User avatar
rodocop
Posts: 1723
Joined: Mon Aug 22, 2016 3:14 pm
Location: Saskatchewan
Has thanked: 606 times
Been thanked: 608 times

Re: [FOR SALE] Picicle a portable games console

Post by rodocop » Tue May 28, 2019 7:57 pm

so i think I have found the issue. I have tried 5 different SD's with all the same freezing issue. whole system freezes after about 1 minute or so. I was thinking the pi might be bad, but I just got my mini usb cable in the mail today, and plugged in. while the picicle is plugged in there is no freezing. once I unplug the cable the system freezes right away, just like it always does. So maybe it is a power issue, and not a pi issue?

What should I be looking for in regard to the power components. I have checked the soldering on all components, and everything appears to be fine. Please let me know if you have any ideas.


EDIT::

Nevermind, it seems to freeze even on power. Now all I can think is the pi is bad. I'll have to desolder it I guess.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest