Need help with screen!
Need help with screen!
I have a BW 3.5 in TFT LCD screen. My zero works with my tv and hdmi. Below are the picture of what I did from what I learned on the forum. My screen is on but nothing happens. I think I wired t correctly. I am in need of help!
- Attachments
-
- IMG_6152.JPG (1.64 MiB) Viewed 7101 times
-
- IMG_6151.JPG (2.59 MiB) Viewed 7101 times
Re: Need help with screen!
Can you try changing the yellow wire to the other pin (one on the left)?
EDIT : Also what are the pins K6 on the video board. Have you checked the wiring? If there is text on the other side of the video board a photo might help
EDIT : Also what are the pins K6 on the video board. Have you checked the wiring? If there is text on the other side of the video board a photo might help
Sent from 20,000 leagues under the sea
My Cardboard GBZ build : http://www.sudomod.com/forum/viewtopic.php?f=9&t=2851
EmulationStation optimization for Pi Zero : http://www.sudomod.com/forum/viewtopic.php?f=8&t=2922
My Cardboard GBZ build : http://www.sudomod.com/forum/viewtopic.php?f=9&t=2851
EmulationStation optimization for Pi Zero : http://www.sudomod.com/forum/viewtopic.php?f=8&t=2922
-
- Posts: 153
- Joined: Wed Jan 18, 2017 1:08 pm
- Has thanked: 13 times
- Been thanked: 8 times
- Lphillimore
- Posts: 993
- Joined: Sat Jan 07, 2017 7:03 pm
- Location: Perth, WA
- Has thanked: 796 times
- Been thanked: 527 times
Re: Need help with screen!
Doesn't look right to me. Usually wire the 5v to main board input then put a jumper over to the Regulator.
Also, not familiar with this board but looks like your 5v is going to wrong regulator?? Assuming its the 8 pin one...
I would move 5v back to main input and test with 12v power supply to ensure screen actually works.
If so, then add the jumper to correct regulator but be sure to then use 5v else you'll blow it
Also, not familiar with this board but looks like your 5v is going to wrong regulator?? Assuming its the 8 pin one...
I would move 5v back to main input and test with 12v power supply to ensure screen actually works.
If so, then add the jumper to correct regulator but be sure to then use 5v else you'll blow it
mintyPi Giveaway [CLOSED]:
http://www.sudomod.com/forum/viewtopic.php?f=38&t=3456
Builds:
GBZ
http://www.sudomod.com/forum/viewtopic.php?f=9&t=2838
mintyPi
http://www.sudomod.com/forum/viewtopic.php?f=32&t=3468
Kite SAIO
http://www.sudomod.com/forum/viewtopic.php?f=9&t=3075
Dreamcast VMU
https://sudomod.com/forum/viewtopic.php ... 133#p62133
http://www.sudomod.com/forum/viewtopic.php?f=38&t=3456
Builds:
GBZ
http://www.sudomod.com/forum/viewtopic.php?f=9&t=2838
mintyPi
http://www.sudomod.com/forum/viewtopic.php?f=32&t=3468
Kite SAIO
http://www.sudomod.com/forum/viewtopic.php?f=9&t=3075
Dreamcast VMU
https://sudomod.com/forum/viewtopic.php ... 133#p62133
-
- Posts: 153
- Joined: Wed Jan 18, 2017 1:08 pm
- Has thanked: 13 times
- Been thanked: 8 times
-
- Posts: 153
- Joined: Wed Jan 18, 2017 1:08 pm
- Has thanked: 13 times
- Been thanked: 8 times
Who is online
Users browsing this forum: Bing [Bot] and 1 guest