Page 1 of 2
Analog stick with Helder 2.2A board
Posted: Sun Feb 05, 2017 7:23 am
by Billy@sudo
I bought Tl-26 psp Analog stick for GBZ project. and i followed wiring of Xaxis, Ground , Yaxis, 5V per manf. but no luck. i tried swaping ground and 5v. still no luck. please help.
Thank you
Re: Analog stick with Helder 2.2A board
Posted: Sun Feb 05, 2017 11:22 pm
by Helder
You need to reprogram the board for analog stick use. 99% of people don't use the stick and if the code for the stick is programed into it there are control issues. Look in the Other Hardware Subforum for a guide on how to program it.
Re: Analog stick with Helder 2.2A board
Posted: Mon Feb 06, 2017 5:30 am
by Billy@sudo
Helder wrote:You need to reprogram the board for analog stick use. 99% of people don't use the stick and if the code for the stick is programed into it there are control issues. Look in the Other Hardware Subforum for a guide on how to program it.
Thank you much. I show that post before posting this. Iy look hard to reprogram. I might give it a try.
Re: Analog stick with Helder 2.2A board
Posted: Mon Feb 06, 2017 6:49 pm
by Billy@sudo
Helder wrote:You need to reprogram the board for analog stick use. 99% of people don't use the stick and if the code for the stick is programed into it there are control issues. Look in the Other Hardware Subforum for a guide on how to program it.
If i program it. Will it work properly? Or still control issues? I thought i bought a board with 1 analog already programmed. Please advice. Thanks
Re: Analog stick with Helder 2.2A board
Posted: Mon Feb 06, 2017 6:52 pm
by Helder
Billy@sudo wrote:Helder wrote:You need to reprogram the board for analog stick use. 99% of people don't use the stick and if the code for the stick is programed into it there are control issues. Look in the Other Hardware Subforum for a guide on how to program it.
If i program it. Will it work properly? Or still control issues? I thought i bought a board with 1 analog already programmed. Please advice. Thanks
The controller has issues if it's programmed for an analog stick and one isn't connected. If you connect the analog stick then there is no issue. If you live in the USA I can program it for you but you will need to pay shipping but I would look at the guides as to how to do it to save time and money.
Re: Analog stick with Helder 2.2A board
Posted: Wed Feb 08, 2017 4:11 am
by Billy@sudo
Helder wrote:Billy@sudo wrote:Helder wrote:You need to reprogram the board for analog stick use. 99% of people don't use the stick and if the code for the stick is programed into it there are control issues. Look in the Other Hardware Subforum for a guide on how to program it.
If i program it. Will it work properly? Or still control issues? I thought i bought a board with 1 analog already programmed. Please advice. Thanks
The controller has issues if it's programmed for an analog stick and one isn't connected. If you connect the analog stick then there is no issue. If you live in the USA I can program it for you but you will need to pay shipping but I would look at the guides as to how to do it to save time and money.
Thanks. I ordered the usbasp amtel programmer. Do i have to power the board to flash it?
Re: Analog stick with Helder 2.2A board
Posted: Wed Feb 08, 2017 12:45 pm
by Helder
The board gets power through the ISP header so just connect it to the PC and into the ISP holes and it should power on to program.
Re: Analog stick with Helder 2.2A board
Posted: Fri Feb 10, 2017 12:18 pm
by Billy@sudo
Helder wrote:The board gets power through the ISP header so just connect it to the PC and into the ISP holes and it should power on to program.
Helder, shoukd i just press program only on usbasp. Because it writes fuses only 1byte. On th guide you posted, some one said that he pressed go under flash and then program. Please let me know.
Thank you.
Re: Analog stick with Helder 2.2A board
Posted: Fri Feb 10, 2017 1:16 pm
by Helder
Billy@sudo wrote:Helder wrote:The board gets power through the ISP header so just connect it to the PC and into the ISP holes and it should power on to program.
Helder, shoukd i just press program only on usbasp. Because it writes fuses only 1byte. On th guide you posted, some one said that he pressed go under flash and then program. Please let me know.
Thank you.
Be sure your Fuses match mine and either Go or Program will work as I've used both many times and always works out in the end.
Re: Analog stick with Helder 2.2A board
Posted: Sat Feb 11, 2017 4:24 am
by Billy@sudo
Helder wrote:Billy@sudo wrote:Helder wrote:The board gets power through the ISP header so just connect it to the PC and into the ISP holes and it should power on to program.
Helder, shoukd i just press program only on usbasp. Because it writes fuses only 1byte. On th guide you posted, some one said that he pressed go under flash and then program. Please let me know.
Thank you.
Be sure your Fuses match mine and either Go or Program will work as I've used both many times and always works out in the end.
Helder, even though it says 1 byte fuse written. My thunstick is now detected and i assigned it as left thumstick u d l r. Is it normal that it wont work with retro pi menu?