Wiring teensy to pi zero.

General GBZ-related chat goes here. Share ideas, tips and tricks, or ask questions that don't fit into the hardware/software help forums.
Post Reply
Ballashoes
Posts: 5
Joined: Tue Jul 11, 2017 1:04 pm

Wiring teensy to pi zero.

Post by Ballashoes » Tue Jul 11, 2017 1:11 pm

I wired my teensy to my pi zero by using this method, with the green and white going to PP22 and 23. Nothing seems to happen with my controls, I haven't tested it with a actual male micro USB to male micro USB but I'll try that soon.

I'm sure I did something wrong or missing something as I'm new to all of this.
Attachments
card6b_rev1.png
I used the VUSB for power and the D+ and - and ground.
card6b_rev1.png (285.33 KiB) Viewed 3166 times
Capture9999.PNG
Capture9999.PNG (703.23 KiB) Viewed 3166 times

snoek09
Posts: 145
Joined: Sat May 20, 2017 3:06 am
Location: Amsterdam, The Netherlands
Has thanked: 48 times
Been thanked: 43 times

Re: Wiring teensy to pi zero.

Post by snoek09 » Tue Jul 11, 2017 2:26 pm

If you could post a picture that would help a lot.
Did you twist the green and white wire to the Pi zero?

Image

I connected a Teensy LC to a USB hub yesterday.
It didn't work at first as some connections where a bit loose and others where a bit bridged. Mainly on the USB hub which was a lot trickier to solder compared to the pads on the Teensy.
After making sure the connections were solid and didn't touch each other it's now working fine.

Ballashoes
Posts: 5
Joined: Tue Jul 11, 2017 1:04 pm

Re: Wiring teensy to pi zero.

Post by Ballashoes » Tue Jul 11, 2017 5:03 pm

snoek09 wrote:
Tue Jul 11, 2017 2:26 pm
If you could post a picture that would help a lot.
Did you twist the green and white wire to the Pi zero?

Image

I connected a Teensy LC to a USB hub yesterday.
It didn't work at first as some connections where a bit loose and others where a bit bridged. Mainly on the USB hub which was a lot trickier to solder compared to the pads on the Teensy.
After making sure the connections were solid and didn't touch each other it's now working fine.
I don't have a picture at the moment, I'm out of town for a couple days. I did not twist it, I'll give that a shot when I get back and double check my connections. Thanks for the reply.

Ballashoes
Posts: 5
Joined: Tue Jul 11, 2017 1:04 pm

Re: Wiring teensy to pi zero.

Post by Ballashoes » Tue Jul 11, 2017 6:25 pm

snoek09 wrote:
Tue Jul 11, 2017 2:26 pm
If you could post a picture that would help a lot.
Did you twist the green and white wire to the Pi zero?

Image

I connected a Teensy LC to a USB hub yesterday.
It didn't work at first as some connections where a bit loose and others where a bit bridged. Mainly on the USB hub which was a lot trickier to solder compared to the pads on the Teensy.
After making sure the connections were solid and didn't touch each other it's now working fine.
Looks like this might work, I'll give that a try. Didn't see that post before I made this one.

snoek09
Posts: 145
Joined: Sat May 20, 2017 3:06 am
Location: Amsterdam, The Netherlands
Has thanked: 48 times
Been thanked: 43 times

Re: Wiring teensy to pi zero.

Post by snoek09 » Wed Jul 12, 2017 1:16 am

Also, did you test the Teensy LC when you hooked it up to a computer?
The button presses should be visible in a text editor for example.

Ballashoes
Posts: 5
Joined: Tue Jul 11, 2017 1:04 pm

Re: Wiring teensy to pi zero.

Post by Ballashoes » Wed Jul 12, 2017 1:30 am

snoek09 wrote:
Wed Jul 12, 2017 1:16 am
Also, did you test the Teensy LC when you hooked it up to a computer?
The button presses should be visible in a text editor for example.
I did not, probably a good idea to make sure everything is working on that front. I forgot to post the link on the last post, http://www.sudomod.com/forum/viewtopic.php?f=8&t=1345

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest