My First GBCM3

Show off your completed Game Boy Zero, or post your build logs here!
vinomer
Posts: 43
Joined: Sat Nov 18, 2017 9:47 am
Has thanked: 1 time
Been thanked: 12 times

Re: My First GBCM3

Post by vinomer » Tue Dec 04, 2018 2:10 pm

They didn't even take the time to remove the excess plastic, or the plastic strings.That's bad customer service. You can always smooth it out using sand paper and spray paint it.
I get my high quality 3D prints from HoolyHoo, you can find his items in the For Sale section. https://sudomod.com/forum/viewforum.php?f=38

phreaky
Posts: 24
Joined: Tue Nov 06, 2018 9:43 am
Has thanked: 2 times
Been thanked: 1 time

Re: My First GBCM3

Post by phreaky » Wed Dec 05, 2018 12:58 pm

Seller response

sure; picture 2 shows the underside of a support area, and the "see through" area is a 0.3MM thick layer which is more of a design issue then a printing issue.
both parts are very small, around 1.4 to 2 cm, and the rough areas are simply support areas which will look that way if supports need to be placed below it. i can reprint and it won't look better.


Not sure how it should look ...

I might consider ordering from here....

User avatar
VeteranGamer
Posts: 1410
Joined: Thu Jan 26, 2017 11:12 am
Location: London, UK
Has thanked: 412 times
Been thanked: 761 times

Re: My First GBCM3

Post by VeteranGamer » Thu Dec 06, 2018 12:22 am

phreaky wrote:
Wed Dec 05, 2018 12:58 pm
Seller response

sure; picture 2 shows the underside of a support area, and the "see through" area is a 0.3MM thick layer which is more of a design issue then a printing issue.
both parts are very small, around 1.4 to 2 cm, and the rough areas are simply support areas which will look that way if supports need to be placed below it. i can reprint and it won't look better.


Not sure how it should look ...

I might consider ordering from here....

this is the issue with 3dHub.....
(and one of the reasons I don't use it anymore)


its a fob off, if ever i saw one.....

to blame the design, without raising any issues with it before proceeding with the order request is NOT acceptable....

also you need to make them aware, that they are not the first person to print this design....
but they are the first person to deliver a below par print

and to say if they print it again (re-print), that the results will be the same (again another fob off)
(they don't want to re-print it)
and that speaks volumes about them rather than the design....


providing you haven't accepted the design within the hub, I'd still argue your case.....
if not....
just clean them up and use them....
once cleaned up a little (there NO need to sand and paint, just clean them up with a pair of snips)
there no need to look elsewhere for another set of prints, they'll work....



.

spacemishka
Posts: 74
Joined: Tue May 29, 2018 6:47 am
Has thanked: 14 times
Been thanked: 13 times

Re: My First GBCM3

Post by spacemishka » Fri Dec 07, 2018 12:30 am

3dhub.......

i ordered some parts in Summer and wasn't satisfied as well. I thought this could be better,...an the parts were not cleaned as well.

phreaky
Posts: 24
Joined: Tue Nov 06, 2018 9:43 am
Has thanked: 2 times
Been thanked: 1 time

Re: My First GBCM3

Post by phreaky » Fri Dec 07, 2018 2:12 am

VeteranGamer wrote:
Thu Dec 06, 2018 12:22 am
this is the issue with 3dHub.....
(and one of the reasons I don't use it anymore)


its a fob off, if ever i saw one.....

to blame the design, without raising any issues with it before proceeding with the order request is NOT acceptable....

also you need to make them aware, that they are not the first person to print this design....
but they are the first person to deliver a below par print

and to say if they print it again (re-print), that the results will be the same (again another fob off)
(they don't want to re-print it)
and that speaks volumes about them rather than the design....


providing you haven't accepted the design within the hub, I'd still argue your case.....
if not....
just clean them up and use them....
once cleaned up a little (there NO need to sand and paint, just clean them up with a pair of snips)
there no need to look elsewhere for another set of prints, they'll work....
thnx again for your advice!

is this part still usable ?as i am not sure what the pins are for but they are not round.
Image

User avatar
VeteranGamer
Posts: 1410
Joined: Thu Jan 26, 2017 11:12 am
Location: London, UK
Has thanked: 412 times
Been thanked: 761 times

Re: My First GBCM3

Post by VeteranGamer » Fri Dec 07, 2018 3:44 am

phreaky wrote:
Fri Dec 07, 2018 2:12 am
VeteranGamer wrote:
Thu Dec 06, 2018 12:22 am
this is the issue with 3dHub.....
(and one of the reasons I don't use it anymore)


its a fob off, if ever i saw one.....

to blame the design, without raising any issues with it before proceeding with the order request is NOT acceptable....

also you need to make them aware, that they are not the first person to print this design....
but they are the first person to deliver a below par print

and to say if they print it again (re-print), that the results will be the same (again another fob off)
(they don't want to re-print it)
and that speaks volumes about them rather than the design....


providing you haven't accepted the design within the hub, I'd still argue your case.....
if not....
just clean them up and use them....
once cleaned up a little (there NO need to sand and paint, just clean them up with a pair of snips)
there no need to look elsewhere for another set of prints, they'll work....
thnx again for your advice!

is this part still usable ?as i am not sure what the pins are for but they are not round.
Image


can you post or link the original design....



.

phreaky
Posts: 24
Joined: Tue Nov 06, 2018 9:43 am
Has thanked: 2 times
Been thanked: 1 time

Re: My First GBCM3

Post by phreaky » Sun Dec 09, 2018 3:30 am

VeteranGamer wrote:
Fri Dec 07, 2018 3:44 am

can you post or link the original design....

.
https://sudomod.com/forum/viewtopic.php?f=57&t=6151 part is from here

Also got a full refund

User avatar
AntFJ
Posts: 88
Joined: Thu Nov 16, 2017 8:09 pm
Has thanked: 17 times
Been thanked: 63 times

Re: My First GBCM3

Post by AntFJ » Tue Dec 11, 2018 10:40 pm

terrible prints... my $130 printer prints way better than that. I'd expect a professional service to at least use supports... i'd try to get my $$ back or a better product. That's embarrassing for them

phreaky
Posts: 24
Joined: Tue Nov 06, 2018 9:43 am
Has thanked: 2 times
Been thanked: 1 time

Re: My First GBCM3

Post by phreaky » Wed Dec 12, 2018 1:43 am

i did get my money back. all parts are usable except the Back Button Bracket and the LCD Bracket. the pins which should hold the siliconpads arrent the correct size

phreaky
Posts: 24
Joined: Tue Nov 06, 2018 9:43 am
Has thanked: 2 times
Been thanked: 1 time

Re: My First GBCM3

Post by phreaky » Wed Dec 12, 2018 1:47 am

I finally had some time to cut and trim the shell so i did :).
didn't drill the holes yet for the X and Y buttons because i have to order a different LCD bracket.
pictures are in the first post.


also bought a GameBoy so i have someting to do while waiting on the orthers parts :)
Image

Post Reply

Who is online

Users browsing this forum: No registered users and 21 guests