Page 1 of 2
1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 1:49 am
by Rroobb21
Finished my 1st Gameboy SNES zero
Kites SAIO
Veco speaker
Original SNES buttons
Original NES dpad
DexTech battery
Kubino machined Case
YaYa box art
Erik_gee rear button bracket
Just want to thank everyone for the awesome parts and help.
I’m abit of a perfectionist and so pleased with how it came out hardly any glue used and all the buttons the same height and feel.
Re: 1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 2:49 am
by YaYa
Thank you for the mention !
Nice build
where di you get that support stand ?
Also, i would advise to take out some kapton from the SoC as you will likely insulate it and thus make it get hotter.
Re: 1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 5:17 am
by Rroobb21
YaYa wrote: ↑Wed Nov 08, 2017 2:49 am
Thank you for the mention !
Nice build
where di you get that support stand ?
Also, i would advise to take out some kapton from the SoC as you will likely insulate it and thus make it get hotter.
Thanks !! All done . Iv had it sitting around for ages can’t remeber where it came from . Il try and find out and let you know
Re: 1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 8:00 am
by Rroobb21
kite wrote: ↑Wed Nov 08, 2017 6:22 am
Looks AMAZING! Top tip that might make assembly slightly easier.. you see where you have hooked the L1 and R1 buttons up by using both of those 3pin cables (and cutting the red pin off both) .. well you could JUST use the "R" one, and wire the RED cable up to L1.. this makes it easy to connect and close up because you don't have to have that extra cable and plug it in when closing it.. (does all this make sense?) .. the labels "L1 L2 R1 R2 etc are just labels they don't actually mean anything, you could plug it into ANY combination and it doesn't matter (because when you "configure input" in ES, you assign the buttons to the function)
otherwise looks AMAZING!
Yep makes perfect sense. Thanks kite
Re: 1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 3:12 pm
by neolith
Nice build!
Is the cartridge glued in?
Re: 1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 11:11 pm
by Rroobb21
neolith wrote: ↑Wed Nov 08, 2017 3:12 pm
Nice build!
Is the cartridge glued in?
No just abit of 3m vhb tape
Re: 1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 11:20 pm
by kubino
Nice! Does it mean my L/R cut fit's Erik bracket without moding?
Re: 1st GBZ build kites SAIO
Posted: Wed Nov 08, 2017 11:56 pm
by erik_gee
kubino wrote: ↑Wed Nov 08, 2017 11:20 pm
Nice! Does it mean my L/R cut fit's Erik bracket without moding?
I'd like to know too haha
PS kubino, I sent you a set of each of my brackets. Did you receive them ?
Re: 1st GBZ build kites SAIO
Posted: Thu Nov 09, 2017 12:09 am
by kubino
erik_gee wrote: ↑Wed Nov 08, 2017 11:56 pm
kubino wrote: ↑Wed Nov 08, 2017 11:20 pm
Nice! Does it mean my L/R cut fit's Erik bracket without moding?
I'd like to know too haha
PS kubino, I sent you a set of each of my brackets. Did you receive them ?
Hi Erik,
can't tell yet as this week I'm at work about 300km away from home. Will let you know next week
Re: 1st GBZ build kites SAIO
Posted: Thu Nov 09, 2017 12:13 am
by erik_gee
kubino wrote: ↑Thu Nov 09, 2017 12:09 am
erik_gee wrote: ↑Wed Nov 08, 2017 11:56 pm
kubino wrote: ↑Wed Nov 08, 2017 11:20 pm
Nice! Does it mean my L/R cut fit's Erik bracket without moding?
I'd like to know too haha
PS kubino, I sent you a set of each of my brackets. Did you receive them ?
Hi Erik,
can't tell yet as this week I'm at work about 300km away from home. Will let you know next week
Oh wow that's far haha no worries
