[Completed]Sushi's GB3-Slim

Sendoushi · Post by **Sendoushi** » Sat Jan 20, 2018 12:57 am

Pretty cool project! Definitely interested in see how it goes.

tinkerBOY · Post by **tinkerBOY** » Sat Jan 20, 2018 1:13 am

Nice work! Can't wait to see how it all fits inside.

Sushi · Post by **Sushi** » Sat Jan 20, 2018 6:19 pm

All done

I've gotta take it apart again so that I can mess with the control setup, but here it is - fully working. I've also gotta put the screen cover on, but whatever.

Photos of final productShow

: IMG_0656.JPG (1.88 MiB) Viewed 5851 times

: IMG_0653.JPG (1.93 MiB) Viewed 5851 times

: IMG_0654.JPG (1.59 MiB) Viewed 5851 times

: IMG_0655.JPG (1.58 MiB) Viewed 5851 times

: IMG_0651.JPG (2.06 MiB) Viewed 5851 times

: IMG_0657.JPG (2.25 MiB) Viewed 5850 times

Sendoushi · Post by **Sendoushi** » Sun Jan 21, 2018 3:55 am

This print looks so good. Did you do it in house? The only thing is the raspberry not being screwed down.

tinkerBOY · Post by **tinkerBOY** » Sun Jan 21, 2018 4:55 am

Will a fan fit?

Sushi · Post by **Sushi** » Sun Jan 21, 2018 10:13 am

Sendoushi wrote: ↑
Sun Jan 21, 2018 3:55 am
This print looks so good. Did you do it in house? The only thing is the raspberry not being screwed down.

I did do the print on my own printer. Thanks

The RPi is actually screwed down, though.

tinkerBOY wrote: ↑
Sun Jan 21, 2018 4:55 am
Will a fan fit?

Maybe if I managed the wiring better. I'd like to rewire the whole thing because a lot of wires were way too long while others were not long enough.

Varthdader · Post by **Varthdader** » Wed Jan 24, 2018 11:35 am

Looks amazing!

Would be super cool to have the STL files to print now that I got a 3d printer.

Thump52 · Post by **Thump52** » Wed Jan 24, 2018 12:49 pm

Looks good, nice build, I would like to see the speakers holes shaped like the Raspberry Pi logo and it would also look cool if you printed it to look like it has a battery opening, just my thoughts, again very nice build.

Sendoushi · Post by **Sendoushi** » Wed Jan 24, 2018 12:53 pm

Did you set safe shutdown and speakers actually? On the first photos didn't seem so.

Sushi · Post by **Sushi** » Wed Jan 24, 2018 3:08 pm

Sendoushi wrote: ↑
Wed Jan 24, 2018 12:53 pm
Did you set safe shutdown and speakers actually? On the first photos didn't seem so.

I programmed the arduino to send a shutdown command when I pulled both triggers and pressed d-pad down. The sound does in fact work, but only in the assembled version. The inside pics aren't complete. I made some wires too short, so I had to solder them with the back partially on. I couldn't take pics at that point

[Completed]Sushi's GB3-Slim

Re: Sushi's GB3-Slim

Re: Sushi's GB3-Slim

Re: Sushi's GB3-Slim

Re: [Completed]Sushi's GB3-Slim

Re: [Completed]Sushi's GB3-Slim

Re: [Completed]Sushi's GB3-Slim

Re: [Completed]Sushi's GB3-Slim

Re: [Completed]Sushi's GB3-Slim

Re: [Completed]Sushi's GB3-Slim

Re: [Completed]Sushi's GB3-Slim

Who is online