Page 1 of 1
First CM3 Build
Posted: Tue Aug 14, 2018 2:25 pm
by swanee639
Decided to go with a Wii theme
- IMG_8191.jpg (1.35 MiB) Viewed 5946 times
- IMG_8186.jpg (1.29 MiB) Viewed 5946 times
- IMG_8189.jpg (1.55 MiB) Viewed 5946 times
- IMG_8190.jpg (1.56 MiB) Viewed 5946 times
- IMG_8192.jpg (1.65 MiB) Viewed 5946 times
- Untitled.png (227.62 KiB) Viewed 5902 times
edit-
after sanding:
- IMG_8208[2195].jpg (1.17 MiB) Viewed 5643 times
Bonus:
- IMG_8166.jpg (1.95 MiB) Viewed 5946 times
The shoulder buttons use the original actions from the Wii classic controller, so the L/R have a spring and conductive pad, and the center two use tactile switches.
The joystick is a 3DS slider and I'm using one of Kite's boards with a CM3
Still working on the fix for that gap you can see in the middle but I need to wait until school starts back up to use their printers
Oh and a thanks/shout out to
Kite for the Circuit Sword/kit
YaYa for the custom Gorilla Glass screen cover
and Dextech for the lipo battery
Re: First CM3 Build
Posted: Tue Aug 14, 2018 2:27 pm
by dryja123
Top notch work, I really like it! Did you print that case?
Re: First CM3 Build
Posted: Tue Aug 14, 2018 2:29 pm
by YaYa
Excellent ! Very good job
and the screen cover fits like a glove
Re: First CM3 Build
Posted: Tue Aug 14, 2018 2:34 pm
by swanee639
dryja123 wrote: ↑Tue Aug 14, 2018 2:27 pm
Top notch work, I really like it! Did you print that case?
Yeah I used Shapeways. It is the SLS Nylon. There are some brackets inside that I printed at my school's fab lab in PLA
Re: First CM3 Build
Posted: Tue Aug 14, 2018 5:12 pm
by VeteranGamer
Nice build.... great work
.
Re: First CM3 Build
Posted: Wed Aug 15, 2018 4:51 am
by Killar
I never been a fan of the Wii.. but i must say that i LOVE IT
Always great to se someone design something new from ground up.. i looks more comfortable/ergonomically than a regular dmg
Re: First CM3 Build
Posted: Wed Aug 15, 2018 7:14 am
by smoothoperator
Awesome! Now if we could get these injection molded and produced you might really be on to something here! Nice work!
Re: First CM3 Build
Posted: Wed Aug 15, 2018 3:11 pm
by ekilla
I like it much. Great work. A little bit like the RS-90, but way better
Re: First CM3 Build
Posted: Thu Aug 16, 2018 6:56 am
by Moonsword
I love the design.
Personally, I would give the outside of the case a sanding to smooth it off, it looks a bit rough in the photos.
But the way you have done the shoulder buttons. I love it.
Re: First CM3 Build
Posted: Sat Aug 18, 2018 3:39 am
by swanee639
Moonsword wrote: ↑Thu Aug 16, 2018 6:56 am
I love the design.
Personally, I would give the outside of the case a sanding to smooth it off, it looks a bit rough in the photos.
But the way you have done the shoulder buttons. I love it.
sage advice. it cleaned up nicely
- IMG_8208[2195].jpg (1.17 MiB) Viewed 5039 times