Kite Circuit Sword & Switch joy con issue
- lord_of_misrule
- Posts: 38
- Joined: Thu Jan 31, 2019 7:44 pm
- Been thanked: 6 times
Kite Circuit Sword & Switch joy con issue
Hey everyone! So I recently decided to update my CS with a switch joy con, but I can only seem to get it to register up & down, not left & right. Any ideas?
I followed the instructions to a tee here:
https://www.sudomod.com/forum/viewtopic ... con#p82270
Any help would be much appreciated!
- L_O_M
I followed the instructions to a tee here:
https://www.sudomod.com/forum/viewtopic ... con#p82270
Any help would be much appreciated!
- L_O_M
- lord_of_misrule
- Posts: 38
- Joined: Thu Jan 31, 2019 7:44 pm
- Been thanked: 6 times
Re: Kite Circuit Sword & Switch joy con issue
...I did not. What is this "joystick calibration" or which you speak?
Re: Kite Circuit Sword & Switch joy con issue
https://github.com/kiteretro/Circuit-Sw ... -joystickslord_of_misrule wrote: ↑Fri Sep 25, 2020 3:40 pm...I did not. What is this "joystick calibration" or which you speak?
I don’t actually know if this is the solution, just trying to help figure it out!
- lord_of_misrule
- Posts: 38
- Joined: Thu Jan 31, 2019 7:44 pm
- Been thanked: 6 times
Re: Kite Circuit Sword & Switch joy con issue
millski wrote: ↑Sat Sep 26, 2020 12:44 amhttps://github.com/kiteretro/Circuit-Sw ... -joystickslord_of_misrule wrote: ↑Fri Sep 25, 2020 3:40 pm...I did not. What is this "joystick calibration" or which you speak?
I don’t actually know if this is the solution, just trying to help figure it out!
Thanks!! I'll give it a go later! Fingers crossed!
- lord_of_misrule
- Posts: 38
- Joined: Thu Jan 31, 2019 7:44 pm
- Been thanked: 6 times
Re: Kite Circuit Sword & Switch joy con issue
Unfortunately, it didn't work :/ the calibration all worked to the letter, but when I go to assign control configs on the main menu, it's still addressing only up & downlord_of_misrule wrote: ↑Sat Sep 26, 2020 9:55 ammillski wrote: ↑Sat Sep 26, 2020 12:44 amhttps://github.com/kiteretro/Circuit-Sw ... -joystickslord_of_misrule wrote: ↑Fri Sep 25, 2020 3:40 pm
...I did not. What is this "joystick calibration" or which you speak?
I don’t actually know if this is the solution, just trying to help figure it out!
Thanks!! I'll give it a go later! Fingers crossed!
- lord_of_misrule
- Posts: 38
- Joined: Thu Jan 31, 2019 7:44 pm
- Been thanked: 6 times
Re: Kite Circuit Sword & Switch joy con issue
I dunno what else to try. When I try configuring it in retropie, it says "already taken"
- lord_of_misrule
- Posts: 38
- Joined: Thu Jan 31, 2019 7:44 pm
- Been thanked: 6 times
Re: Kite Circuit Sword & Switch joy con issue
Hmm, maybe try resetting your controller configuration?
Retropie setup>Manage packages>Manage core packages>Emulationstation>Configuration/options> Clear/Reset Emulation Station input configuration>Yes>OK then keep exiting and reboot. Be careful when configuring the joystick as the joycon seems much more sensitive than the ps sticks I’ve used before, it’s very easy to tap it just slightly and it will register as a movement in the controller configuration, or not push precisely up or down and it registers as left or right instead.
Fingers crossed you’ll get it working properly soon!
Retropie setup>Manage packages>Manage core packages>Emulationstation>Configuration/options> Clear/Reset Emulation Station input configuration>Yes>OK then keep exiting and reboot. Be careful when configuring the joystick as the joycon seems much more sensitive than the ps sticks I’ve used before, it’s very easy to tap it just slightly and it will register as a movement in the controller configuration, or not push precisely up or down and it registers as left or right instead.
Fingers crossed you’ll get it working properly soon!
Who is online
Users browsing this forum: No registered users and 1 guest