Page 1 of 2
Kite Circuit Sword & Switch joy con issue
Posted: Thu Sep 24, 2020 5:27 pm
by lord_of_misrule
Hey everyone! So I recently decided to update my CS with a switch joy con, but I can only seem to get it to register up & down, not left & right. Any ideas?
I followed the instructions to a tee here:
https://www.sudomod.com/forum/viewtopic ... con#p82270
- IMG_20200924_190906772_HDR.jpg (3.18 MiB) Viewed 9188 times
- IMG_20200924_190917814_HDR.jpg (2.45 MiB) Viewed 9188 times
- IMG_20200924_190930022_HDR.jpg (2.35 MiB) Viewed 9188 times
- IMG_20200924_191108533.jpg (3.1 MiB) Viewed 9188 times
- IMG_20200924_191113554.jpg (2.6 MiB) Viewed 9188 times
Any help would be much appreciated!
- L_O_M
Re: Kite Circuit Sword & Switch joy con issue
Posted: Fri Sep 25, 2020 6:28 am
by millski
Your wiring looks ok to me. Did you run the joystick calibration from ssh?
Re: Kite Circuit Sword & Switch joy con issue
Posted: Fri Sep 25, 2020 3:40 pm
by lord_of_misrule
millski wrote: ↑Fri Sep 25, 2020 6:28 am
Your wiring looks ok to me. Did you run the joystick calibration from ssh?
...I did not. What is this "joystick calibration" or which you speak?
Re: Kite Circuit Sword & Switch joy con issue
Posted: Sat Sep 26, 2020 12:44 am
by millski
lord_of_misrule wrote: ↑Fri Sep 25, 2020 3:40 pm
millski wrote: ↑Fri Sep 25, 2020 6:28 am
Your wiring looks ok to me. Did you run the joystick calibration from ssh?
...I did not. What is this "joystick calibration" or which you speak?
https://github.com/kiteretro/Circuit-Sw ... -joysticks
I don’t actually know if this is the solution, just trying to help figure it out!
Re: Kite Circuit Sword & Switch joy con issue
Posted: Sat Sep 26, 2020 9:55 am
by lord_of_misrule
Thanks!! I'll give it a go later! Fingers crossed!
Re: Kite Circuit Sword & Switch joy con issue
Posted: Sat Sep 26, 2020 11:43 am
by lord_of_misrule
lord_of_misrule wrote: ↑Sat Sep 26, 2020 9:55 am
Thanks!! I'll give it a go later! Fingers crossed!
Unfortunately, it didn't work :/ the calibration all worked to the letter, but when I go to assign control configs on the main menu, it's still addressing only up & down
Re: Kite Circuit Sword & Switch joy con issue
Posted: Sat Sep 26, 2020 4:14 pm
by millski
Did the calibration have values for both x and y? When you configure the input is it showing x+\- or y+\- for up and down?
Re: Kite Circuit Sword & Switch joy con issue
Posted: Tue Sep 29, 2020 4:14 pm
by lord_of_misrule
millski wrote: ↑Sat Sep 26, 2020 4:14 pm
Did the calibration have values for both x and y? When you configure the input is it showing x+\- or y+\- for up and down?
- IMG_20200929_175846251.jpg (1.49 MiB) Viewed 8807 times
I dunno what else to try. When I try configuring it in retropie, it says "already taken"
Re: Kite Circuit Sword & Switch joy con issue
Posted: Tue Sep 29, 2020 4:16 pm
by lord_of_misrule
- IMG_20200929_175825247.jpg (1.38 MiB) Viewed 8806 times
Shit sorry images are so crummy
- IMG_20200929_175818606.jpg (1.8 MiB) Viewed 8806 times
Re: Kite Circuit Sword & Switch joy con issue
Posted: Wed Sep 30, 2020 1:36 am
by millski
Hmm, maybe try resetting your controller configuration?
Retropie setup>Manage packages>Manage core packages>Emulationstation>Configuration/options> Clear/Reset Emulation Station input configuration>Yes>OK then keep exiting and reboot. Be careful when configuring the joystick as the joycon seems much more sensitive than the ps sticks I’ve used before, it’s very easy to tap it just slightly and it will register as a movement in the controller configuration, or not push precisely up or down and it registers as left or right instead.
Fingers crossed you’ll get it working properly soon!