[Guide 02] Few controls don't work
[Guide 02] Few controls don't work
Hi,
I have a problem... I do the tutorial N°2 (I sold the controls to the teensy, I program it with arduino), I verify with my multimeter that all connections are good and I put hot glue, but when I put the board in the game boy and I connect it to Snes9x on my computer few controls don't work (Left, Down, A & B). I don't understand, however all is good, no ?
I had this problem one week ago, so this morning I took off the glue and I soldered it again but I have still the same problem (and I damaged the PCB...). I think the problem come from the Game-Boy controls, no ? In fact I don't know what to do And maybe I will have to buy another Game-Boy (because the PCB damaged).
EDIT : I found that ( common ground dmg button pcb (A/B/X/Y version) ): http://store.kitsch-bent.com/product/co ... -y-version
It could be easier, no ?
I have a problem... I do the tutorial N°2 (I sold the controls to the teensy, I program it with arduino), I verify with my multimeter that all connections are good and I put hot glue, but when I put the board in the game boy and I connect it to Snes9x on my computer few controls don't work (Left, Down, A & B). I don't understand, however all is good, no ?
I had this problem one week ago, so this morning I took off the glue and I soldered it again but I have still the same problem (and I damaged the PCB...). I think the problem come from the Game-Boy controls, no ? In fact I don't know what to do And maybe I will have to buy another Game-Boy (because the PCB damaged).
EDIT : I found that ( common ground dmg button pcb (A/B/X/Y version) ): http://store.kitsch-bent.com/product/co ... -y-version
It could be easier, no ?
- Kilren
- Posts: 574
- Joined: Wed May 11, 2016 4:40 pm
- Location: Washington, USA
- Has thanked: 35 times
- Been thanked: 84 times
Re: [Guide 02] Few controls don't work
That PCB will help you out, and because of it you don't have to buy a new DMG.AlexKidd2 wrote:I had this problem one week ago, so this morning I took off the glue and I soldered it again but I have still the same problem (and I damaged the PCB...). I think the problem come from the Game-Boy controls, no ? In fact I don't know what to do
EDIT : I found that ( common ground dmg button pcb (A/B/X/Y version) ): http://store.kitsch-bent.com/product/co ... -y-version
It could be easier, no ?
As for the buttons, there could be several reasons. Are you wiring to the GPIO or to a Teensy? Check your connection before you glue stuff into position. Double check that your silicone pads are installed and that your buttons are making contact with the board...
Also, take a picture and upload it here so we can see how and where you wired things (both from the PCB>GPIO or PCB>TEENSY>RPI0) so we can help troubleshoot and see potential problems.
Re: [Guide 02] Few controls don't work
A TeensyKilren wrote:Are you wiring to the GPIO or to a Teensy?
I checked and it was great.Check your connection before you glue stuff into position.
Thank you for this tip, I didn't do that and I will do the next time. I ordered a custom PCB because I damaged my actual DMG PCB, I think it will be 1000x easier !Double check that your silicone pads are installed and that your buttons are making contact with the board...
Here a picture of my Teensy. I know the solders are ugly
- Kilren
- Posts: 574
- Joined: Wed May 11, 2016 4:40 pm
- Location: Washington, USA
- Has thanked: 35 times
- Been thanked: 84 times
Re: [Guide 02] Few controls don't work
A couple more tips. Make sure that you twist your wire ends so you don't have any frays. Touching wires will stop a connection and possibly even short out your board. Once twisted, prime them with solder before soldering to the board. It helps with soldering, wire fray, and makes it look cleaner.AlexKidd2 wrote:A TeensyKilren wrote:Are you wiring to the GPIO or to a Teensy?I checked and it was great.Check your connection before you glue stuff into position.Thank you for this tip, I didn't do that and I will do the next time. I ordered a custom PCB because I damaged my actual DMG PCB, I think it will be 1000x easier !Double check that your silicone pads are installed and that your buttons are making contact with the board...
Here a picture of my Teensy. I know the solders are ugly
Second tip for troubleshooting: open up a word pad and check to see if you have button input. Sometimes your emulator has the problem in software config. That'll check to see if it's software or hardware.
Re: [Guide 02] Few controls don't work
Thank you for the first tip. I saw it in the videos but I didn't do it when soldering to my teensy.Second tip for troubleshooting: open up a word pad and check to see if you have button input. Sometimes your emulator has the problem in software config. That'll check to see if it's software or hardware.
Connect the Teensy to a word pad ? What is a word pad, and how to do ?
- Robots86
- Posts: 268
- Joined: Thu May 05, 2016 1:18 am
- Location: Birmingham, UK
- Has thanked: 39 times
- Been thanked: 28 times
Re: [Guide 02] Few controls don't work
AlexKidd2 wrote:Thank you for the first tip. I saw it in the videos but I didn't do it when soldering to my teensy.Second tip for troubleshooting: open up a word pad and check to see if you have button input. Sometimes your emulator has the problem in software config. That'll check to see if it's software or hardware.
Connect the Teensy to a word pad ? What is a word pad, and how to do ?
Connect to a PC. If you have programmed as a keyboard you can type in wordpad or similar program
Re: [Guide 02] Few controls don't work
All my buttons work, then my down will just stop intermittently, then it will start working again it's a strange one. I'm using a teensy.
Re: [Guide 02] Few controls don't work
Think I've fixed it my left and up was touching each other up ha
ijimbob wrote:All my buttons work, then my down will just stop intermittently, then it will start working again it's a strange one. I'm using a teensy.
- Robots86
- Posts: 268
- Joined: Thu May 05, 2016 1:18 am
- Location: Birmingham, UK
- Has thanked: 39 times
- Been thanked: 28 times
Re: [Guide 02] Few controls don't work
Im using a teensy and having trouble with my right and b buttons....
- Fleder
- Posts: 849
- Joined: Thu May 05, 2016 9:04 am
- Location: Germany
- Has thanked: 183 times
- Been thanked: 258 times
Re: [Guide 02] Few controls don't work
After or before the teensy?Robots86 wrote:Im using a teensy and having trouble with my right and b buttons....
Who is online
Users browsing this forum: No registered users and 1 guest