[FOR SALE][Worldwide] 3D-Printed Screw Brackets

[wermy]

Would anyone be interested if I got a small run of these printed for EU shipping? I reckon I could get them done for £5 a piece, shipped.

Awesome, I was hoping someone would pop up for EU shipping.

[benoliver999]

Would anyone be interested if I got a small run of these printed for EU shipping? I reckon I could get them done for £5 a piece, shipped.

Awesome, I was hoping someone would pop up for EU shipping.

I am getting one made to see how it turns out, I went for black ABS - I'll post the results. It's cheap to do, and part of the cost is a fixed fee so the more I get in one go, the cheaper they will be per-unit.

Thanks so much for posting the stl Wermy, this is the one part of the build I was nervous about!

[RazorX]

Would anyone be interested if I got a small run of these printed for EU shipping? I reckon I could get them done for £5 a piece, shipped.

i would be interested

[wermy]

Would anyone be interested if I got a small run of these printed for EU shipping? I reckon I could get them done for £5 a piece, shipped.

Awesome, I was hoping someone would pop up for EU shipping.

I am getting one made to see how it turns out, I went for black ABS - I'll post the results. It's cheap to do, and part of the cost is a fixed fee so the more I get in one go, the cheaper they will be per-unit.

Thanks so much for posting the stl Wermy, this is the one part of the build I was nervous about!

Hey no problem! ABS worked alright for me but I got the feeling it would be a little more prone to the screw holes stripping. Polycarbonate felt much sturdier with repeated screwing/unscrewing. I'm sure ABS will work fine too as long as you're careful.

I printed at 100% infill, 0.2mm layer height, 3 top solid layers, 2 bottom, 2 outline shells.

[Oxodao]

A friend of mine printed one to me
If you dont know anyone take à look at 3dhub.com
Thanks wermy

[benoliver999]

Awesome, I was hoping someone would pop up for EU shipping.

I am getting one made to see how it turns out, I went for black ABS - I'll post the results. It's cheap to do, and part of the cost is a fixed fee so the more I get in one go, the cheaper they will be per-unit.

Thanks so much for posting the stl Wermy, this is the one part of the build I was nervous about!

Hey no problem! ABS worked alright for me but I got the feeling it would be a little more prone to the screw holes stripping. Polycarbonate felt much sturdier with repeated screwing/unscrewing. I'm sure ABS will work fine too as long as you're careful.

I printed at 100% infill, 0.2mm layer height, 3 top solid layers, 2 bottom, 2 outline shells.

I added a polycarbonate one to the order, it didn't cost much more - I'll post them both when they arrive and report back.

EDIT - I take it back! No one will take my PC order! I'll wait for the ABS to arrive, assess it then try harder with the PC if ABS sucks.

[NyaSu]

I printed at 100% infill, 0.2mm layer height, 3 top solid layers, 2 bottom, 2 outline shells.

Hello,

Can you tell me what's its weight ?

Thanks.

[Lanceomni]

In for one.

[wermy]

I printed at 100% infill, 0.2mm layer height, 3 top solid layers, 2 bottom, 2 outline shells.

Hello,

Can you tell me what's its weight ?

Thanks.

My slicing program says about 3 grams-ish.

[Akina86]

Great minds think alike! i did this too and it works great! i also messed around with control boards using the conductive tape method you used for the additional buttons, but eventually bought a kitch board.

IMG_1686.JPG (87.6 KiB) Viewed 10515 times

IMG_1675.JPG (135.5 KiB) Viewed 10515 times