Page 1 of 2

CM3 Rockerswitch not working

Posted: Fri May 03, 2019 4:21 am
by phreaky
Hi there,

finally had to time to assemble everything but it seems the rocker switch for the volume control doesnt function...
i followed this instruction:

How do I enable the digital volume rocker switch
Solder a 'navigation switch' (example) to the main board (under where the battery connector is)
Enable SSH and check that the Circuit Sword is connected to Wi-Fi then log in to the Raspberry Pi Compute Module 3 Lite using SSH
Run the command sudo service cs-hud stop then run the command python Circuit-Sword/cs-configure.py
Press 9 then press ENTER
Press ENTER again then check that the command output reads Digital rocker enabled: 1
Press X then press ENTER
Run the command sudo service cs-hud start


but noting happens when using the switch in menu or in game

Re: CM3 Rockerswitch not working

Posted: Fri May 03, 2019 5:00 am
by kite
Could you show the output from the cs-configure.py command, you know where it shows you all the values when you just press ENTER?

Also, what version of the board do you have?

Re: CM3 Rockerswitch not working

Posted: Fri May 03, 2019 7:05 am
by phreaky
kite wrote:
Fri May 03, 2019 5:00 am
Could you show the output from the cs-configure.py command, you know where it shows you all the values when you just press ENTER?

Also, what version of the board do you have?
will upload the output as soons as i get home.

i have the version you send out this march

Re: CM3 Rockerswitch not working

Posted: Fri May 03, 2019 11:36 am
by phreaky
kite wrote:
Fri May 03, 2019 5:00 am
Could you show the output from the cs-configure.py command, you know where it shows you all the values when you just press ENTER?

Also, what version of the board do you have?
here is the picture

Image

Re: CM3 Rockerswitch not working

Posted: Mon May 06, 2019 7:47 am
by phreaky
is this the correct info ?

Re: CM3 Rockerswitch not working

Posted: Tue May 07, 2019 9:09 am
by kite
Yep, ok looks good, sorry for slow reply! Could you collect the logs and upload (or put on pastebin or something) https://github.com/kiteretro/Circuit-Sw ... -log-files

Re: CM3 Rockerswitch not working

Posted: Wed May 08, 2019 2:11 am
by phreaky
kite wrote:
Tue May 07, 2019 9:09 am
Yep, ok looks good, sorry for slow reply! Could you collect the logs and upload (or put on pastebin or something) https://github.com/kiteretro/Circuit-Sw ... -log-files
will do when i get back home :) thnx

Re: CM3 Rockerswitch not working

Posted: Wed May 08, 2019 9:23 am
by phreaky

Re: CM3 Rockerswitch not working

Posted: Wed May 08, 2019 9:34 am
by kite
No errors so that's a good thing, could you show a picture of your soldering of the rocker? Specifically the BOTTOM pad on the outside, as this is GND.

Related to the above, could you with a multimeter in resistance mode, measure the resistance of the bottom most pad (the one that is kinda under the plastic lever a bit) and another GND point, it should read something like 0.01 ohms (or beep as a short).

Re: CM3 Rockerswitch not working

Posted: Wed May 08, 2019 11:04 am
by phreaky
kite wrote:
Wed May 08, 2019 9:34 am
No errors so that's a good thing, could you show a picture of your soldering of the rocker? Specifically the BOTTOM pad on the outside, as this is GND.

Related to the above, could you with a multimeter in resistance mode, measure the resistance of the bottom most pad (the one that is kinda under the plastic lever a bit) and another GND point, it should read something like 0.01 ohms (or beep as a short).
Is this what you mean?
Image