I've been trying to get this working for a while and I've also checked my wiring, everything checks out,
I've got one working and it works when I use jstest /dev/input/js0 but the second one get nothing, is there anything else I need to do to get the second one working?
I did also go through the steps on here https://github.com/kiteretro/Circuit-Sw ... -Sword-FAQ
Thanks,
Joystick 2 not working Circuit sword V1.1E
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Joystick 2 not working Circuit sword V1.1E
Can you show the output of the configuration.py command? When run normally or just pressing ENTER it will show the config. Also the wiring of how you have connected it
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Joystick 2 not working Circuit sword V1.1E
It's part of the steps you would have to follow to enable it, which are here at the link you provided: https://github.com/kiteretro/Circuit-Sw ... -joysticks
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Re: Joystick 2 not working Circuit sword V1.1E
My bad!
Here is the config (attatched)
Also here's the wiring.. https://drive.google.com/file/d/14r56QV ... -M9s-/view
My camera can't focus but its wired like the other one I have in there and that's working fine
Here is the config (attatched)
Also here's the wiring.. https://drive.google.com/file/d/14r56QV ... -M9s-/view
My camera can't focus but its wired like the other one I have in there and that's working fine
- Attachments
-
- PIJOYSTICK.PNG (14.53 KiB) Viewed 6930 times
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Joystick 2 not working Circuit sword V1.1E
Ah, i have a feeling you have hit an issue that was on the early boards the issue is that the Arduino code had a bug that didn't enable joystick 2! I only just remembered about it now based on some of the output of that command not coming back correctly (older firmware).
Could you please follow these steps to get it updated: https://github.com/kiteretro/Circuit-Sw ... controller
Could you please follow these steps to get it updated: https://github.com/kiteretro/Circuit-Sw ... controller
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Who is online
Users browsing this forum: No registered users and 1 guest