Is this under extruding or possible bad filament

Need help with or have a question about your 3d printer? Ask it here!
User avatar
DeltaShadow
Posts: 63
Joined: Thu May 05, 2016 9:53 am
Been thanked: 2 times

Re: Is this under extruding or possible bad filament

Post by DeltaShadow » Wed Feb 14, 2018 5:51 am

goodBEan wrote:
Tue Feb 13, 2018 7:45 pm
Its a failure. still kinda hollow, I cranked it all up as much as I could. Going to Microcenter to see if they can do something.
https://imgur.com/a/0xHuC
That is probably a good idea. Is your printing issue strictly this filament/ do you have any other rolls that you can test to see if this is an isolated issue. I have not used that filament brand so I do not know what the quality is. In my experience with my maker select which is basically a re-branded WanHao Duplicator, I have not had temperature drops like that on my printer.

User avatar
goodBEan
Posts: 116
Joined: Wed Sep 06, 2017 7:06 pm
Has thanked: 18 times
Been thanked: 30 times

Re: Is this under extruding or possible bad filament

Post by goodBEan » Wed Feb 14, 2018 7:08 am

I tested with a black pla that I have (same brand and everything) and it worked just fine with all normally settings. Same model and everything.

User avatar
DeltaShadow
Posts: 63
Joined: Thu May 05, 2016 9:53 am
Been thanked: 2 times

Re: Is this under extruding or possible bad filament

Post by DeltaShadow » Wed Feb 14, 2018 10:17 am

Then in my mind it is an issue with the filament

User avatar
goodBEan
Posts: 116
Joined: Wed Sep 06, 2017 7:06 pm
Has thanked: 18 times
Been thanked: 30 times

Re: Is this under extruding or possible bad filament

Post by goodBEan » Wed Feb 14, 2018 8:47 pm

I went to micro center and got it exchanged (same type different color). Doing another test print now. Not really optimistic about it.

The thing is I got my printer and my 2 pla rolls for christmas. I ran out of one of them on sunday and thus picked up another one just like it (as I thought), and this whole thing got started. If this does not fix it I am going to stop buying the inland pla locally and either switch to abs or buy pla from somewhere else.

User avatar
goodBEan
Posts: 116
Joined: Wed Sep 06, 2017 7:06 pm
Has thanked: 18 times
Been thanked: 30 times

Re: Is this under extruding or possible bad filament

Post by goodBEan » Wed Feb 14, 2018 10:03 pm

Same thing.
https://imgur.com/a/PPtsG

Starts strong then gets worse.

ICMF
Posts: 279
Joined: Mon Mar 06, 2017 1:52 pm
Has thanked: 3 times
Been thanked: 97 times

Re: Is this under extruding or possible bad filament

Post by ICMF » Thu Feb 15, 2018 8:02 am

Inland is a popular, reputable, quality brand. It's not the filament. Something is wrong with your setup - either mechanically or in your slicer settings.

You need to start troubleshooting from the ground up. Three places I'd start: is your filament feeding correctly (is the spool sticking/catching? blockages in the stepper motor? bowden tubes clean and inserted correctly); is your hotend okay (inspect for damage; do a cold pull on the filament to check the interior); are your slicer settings correct (filament diameter, extrusion multiplier, etc.

Also, you need to adjust your bed height - your nozzle is too far from the bed.

https://all3dp.com/1/common-3d-printing ... -extrusion
https://all3dp.com/1/common-3d-printing ... re-missing

Nixon
Posts: 6
Joined: Tue Feb 13, 2018 3:54 am
Has thanked: 1 time
Been thanked: 3 times

Re: Is this under extruding or possible bad filament

Post by Nixon » Fri Feb 16, 2018 3:28 am

ICMF wrote:
Thu Feb 15, 2018 8:02 am
Inland is a popular, reputable, quality brand. It's not the filament. Something is wrong with your setup - either mechanically or in your slicer settings.

He's tested it with a different roll of the same brand of filament with the same settings and it worked correctly. Guessing it was just a bad batch of filament.
goodBEan wrote:
Wed Feb 14, 2018 7:08 am
I tested with a black pla that I have (same brand and everything) and it worked just fine with all normally settings. Same model and everything.

User avatar
goodBEan
Posts: 116
Joined: Wed Sep 06, 2017 7:06 pm
Has thanked: 18 times
Been thanked: 30 times

Re: Is this under extruding or possible bad filament

Post by goodBEan » Fri Feb 16, 2018 9:20 pm

After reading those links provided by icmf, I decided to try a quick experiment. Right now I am doing the duck test with that gray spool with some new experimental profile meant to combat underextrusion. I simply I am running at 220 c, bed 60c, slower speed 30 , and a fillament flow of 110%. So far it looks promising.

I brought this up on reddit and somebody else noticed
https://www.reddit.com/r/3Dprinting/com ... nland_pla/

User avatar
goodBEan
Posts: 116
Joined: Wed Sep 06, 2017 7:06 pm
Has thanked: 18 times
Been thanked: 30 times

Re: Is this under extruding or possible bad filament

Post by goodBEan » Sat Feb 17, 2018 3:44 pm

Well I tested with a slower speed and filament flow of 150%. We have a complete duck, but there is some cosmetic problems. It looks bad around the nec, but its sturdy.
https://imgur.com/a/kxMST

I think I am close to a solution.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest