Did you see my previous post with pictures on how I tackled this issue? I cut the screw hole tab off of the bigger bracket which allowed a standard DMG screw to work for the smaller tactile backer bracket perfect. I then used (2) M2x10mm flathead machine screws with nuts to secure the power switch bracket. Very solid and works flawlessly. A dummy cartridge in the cartridge bay will cover the screw heads.sygyzy wrote: ↑Fri Mar 30, 2018 2:18 pmHi, I finally got everything fitted thanks for the pictures above and it works great. My button has a nice backing and pushing it in doesn't cause and shifting. However, I am having a simple problem and I am wondering if anyone else is facing it as well. The screw that goes through the red and green part is not long enough to reach the hole in the case. In other words, the 3d printed parts are too thick. I am confident the prints I made are accurate to the 3D models. I also got extra sets of Gameboy DMG screws and even with slight variances, none of the threading seems to catch into the case slot.
Right now, the setup is pretty stable but only because it's being held stiff by the screw. This provides some support but you can easily wiggle the green/red section side to side. Nothing is tightened.
Is there a comparable screw size someone can recommend? Thread size and length would be appreciated.
Thanks in advance.
Glue Less Support Bracket for Kite's Mode/Power Switch Board
-
- Posts: 104
- Joined: Tue Apr 25, 2017 2:59 pm
- Location: Michigan, USA
- Has thanked: 78 times
- Been thanked: 40 times
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
- Kayumba
- Posts: 73
- Joined: Mon Sep 25, 2017 12:36 am
- Location: France
- Has thanked: 8 times
- Been thanked: 17 times
- Contact:
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
Can you print it for me? And how much it will cost ?
I'am afraid that "ModePowerBracket" will be difficult to print for me.
I'am afraid that "ModePowerBracket" will be difficult to print for me.
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
HoolyHoo,
Any update on the fan mount that you mentioned?
Sorry if I just missed the post somewhere
Any update on the fan mount that you mentioned?
Sorry if I just missed the post somewhere
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
Should have that available this week, hopefully
-
- Posts: 2
- Joined: Wed Aug 24, 2016 3:29 pm
- Contact:
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
I don't have a 3D printer is there anyway I could order a couple from you?
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
Sure, just PM meSaintwoody wrote: ↑Thu May 31, 2018 2:59 pmI don't have a 3D printer is there anyway I could order a couple from you?
-
- Posts: 4
- Joined: Sun Aug 05, 2018 1:54 pm
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
I also don't have a 3D printer, how could I order this one from you ?
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
Same as above, just PM mecharbonlaurent wrote: ↑Mon Aug 27, 2018 4:46 amI also don't have a 3D printer, how could I order this one from you ?
-
- Posts: 4
- Joined: Sun Aug 05, 2018 1:54 pm
-
- Posts: 4
- Joined: Sun Aug 05, 2018 1:54 pm
Who is online
Users browsing this forum: No registered users and 1 guest