Page 1 of 5

CM3 Circuit Sword Fan Cartridge

Posted: Fri Apr 06, 2018 8:32 am
by HoolyHoo
Ok guys, for the many that have asked, here is what I think is the final version of my CM3 fan cartridge for Kites awesome CS.
CM3CartFan2.png
CM3CartFan2.png (1.07 MiB) Viewed 6462 times
CM3CartFan1.png
CM3CartFan1.png (1.03 MiB) Viewed 6462 times
The cart itself needs no glue as everything is either snapped on or screwed into place. In the files I have included the front and back and front halves of the cart. Those halves snap together so nothing else needed there. Make sure to screw the fan in first. I have also included in the download a small tab that is used to secure the cart to existing GB shell screw post. No glue necessary to keep cart in. Print two of those if you are not using my Power/Mode support bracket or print the modified one I have included that has the tab already built in and then you will only need on tab on the right side and the new Power/Mode bracket on the left.

Lots of time goes into making and testing these designs so....
If Downloading, and Want to See More Designs in the Future, Please Consider Using the Button :D :
Image
STL DownloadShow
CM3CartFan.zip
(1.96 MiB) Downloaded 590 times

Re: CM3 Circuit Sword Fan Cartridge

Posted: Fri Apr 06, 2018 9:52 am
by Adim01
Nice work you did there :D
Did you benchmark the performance in relation to the original way? Would be nice to see :lol:

Re: CM3 Circuit Sword Fan Cartridge

Posted: Fri Apr 06, 2018 10:01 am
by HoolyHoo
Adim01 wrote:
Fri Apr 06, 2018 9:52 am
Nice work you did there :D
Did you benchmark the performance in relation to the original way? Would be nice to see :lol:
Lol, maybe you can provide us that info on a PowerPoint with bar graphs. 😂

Seriously, I will wait on feedback from you guys. 😉

Re: CM3 Circuit Sword Fan Cartridge

Posted: Fri Apr 06, 2018 10:27 am
by Adim01
HoolyHoo wrote:
Fri Apr 06, 2018 10:01 am
Adim01 wrote:
Fri Apr 06, 2018 9:52 am
Nice work you did there :D
Did you benchmark the performance in relation to the original way? Would be nice to see :lol:
Lol, maybe you can provide us that info on a PowerPoint with bar graphs. 😂

Seriously, I will wait on feedback from you guys. 😉

Hahhahaha I will see what I can do if I get my hands on one, but first I have to source a 3d printing service that uses resin. ;)
And I never really used PowerPoint, so you have to bear with some good old open Office :lol:

Re: CM3 Circuit Sword Fan Cartridge

Posted: Sun Apr 08, 2018 9:57 am
by cowdog360
Adim01 wrote:
Fri Apr 06, 2018 10:27 am
HoolyHoo wrote:
Fri Apr 06, 2018 10:01 am
Adim01 wrote:
Fri Apr 06, 2018 9:52 am
Nice work you did there :D
Did you benchmark the performance in relation to the original way? Would be nice to see :lol:
Lol, maybe you can provide us that info on a PowerPoint with bar graphs. 😂

Seriously, I will wait on feedback from you guys. 😉

Hahhahaha I will see what I can do if I get my hands on one, but first I have to source a 3d printing service that uses resin. ;)
And I never really used PowerPoint, so you have to bear with some good old open Office :lol:
You could always use shapeways and have it done in their SLS process, which looks very nice!

Re: CM3 Circuit Sword Fan Cartridge

Posted: Mon Apr 09, 2018 9:15 am
by dryja123
The fan cartridge looks great!

20180409_111624.jpg
20180409_111624.jpg (3.46 MiB) Viewed 6301 times

Re: CM3 Circuit Sword Fan Cartridge

Posted: Mon Apr 09, 2018 10:10 am
by Nicode70
yes it does! is there any way to paint it?

Re: CM3 Circuit Sword Fan Cartridge

Posted: Mon Apr 09, 2018 12:46 pm
by sygyzy
Nicode70 wrote:
Mon Apr 09, 2018 10:10 am
yes it does! is there any way to paint it?
Yes, you paint it.

---

Great job Hoolyhoo!

Re: CM3 Circuit Sword Fan Cartridge

Posted: Mon Apr 09, 2018 12:49 pm
by Adim01
cowdog360 wrote:
Sun Apr 08, 2018 9:57 am
Adim01 wrote:
Fri Apr 06, 2018 10:27 am
HoolyHoo wrote:
Fri Apr 06, 2018 10:01 am


Lol, maybe you can provide us that info on a PowerPoint with bar graphs. 😂

Seriously, I will wait on feedback from you guys. 😉

Hahhahaha I will see what I can do if I get my hands on one, but first I have to source a 3d printing service that uses resin. ;)
And I never really used PowerPoint, so you have to bear with some good old open Office :lol:
You could always use shapeways and have it done in their SLS process, which looks very nice!
Yeah i thought about it too but i quoted the stl's and they wanted something around 100€ so i didn't go with them, i instead found a lokal SLA printig service on treatstock who did all the parts for around 15,50$ so about 13€.
this is the production picture they send me.
Will post an update how they turned out. :D

Re: CM3 Circuit Sword Fan Cartridge

Posted: Mon Apr 09, 2018 3:01 pm
by HoolyHoo
Did some initial test on the airflow since I was finally able to come close to completing my build. I can tell you that it looks very promising. Fan blows warm air out as intended and temperature drops quickly to stop the fan. Testing was done without a heat sink :o so I imagine when I do place one it should be that much better. Looking to use a flatter larger one since there is space with the fan relocated. Very impressed :D