Idea: HoolyHoo PCB Template

Share your STL files, CAD design files, etc. here!
Post Reply
Sasherz
Posts: 77
Joined: Wed Jul 26, 2017 2:50 pm
Location: Norway
Has thanked: 6 times
Been thanked: 6 times

Idea: HoolyHoo PCB Template

Post by Sasherz » Fri Apr 20, 2018 1:07 pm

I am sorry if this is the wrong place to ask.
But Im not good in 3D Design, I dont even have a 3D Printer myself.

long story short.
I bout this PCB from HoolyHoo
https://sudomod.com/forum/viewtopic.php?f=38&t=5665
I tryed drilling on a test case to see if it would fit, but, it ended up crookid.
Cause of the height from the PCB to the shell has a few mm gap, and its enough to throw the drilling off, making the buttons not look neet on the backside.
som the holes might end up being higher up, lower, closer together, etc.

so my idea for a template is.

It doesnt need to be more than a few mm thick and would sit inside the GB shell for accurate drilling.
it might sound useless, but for the perfectionist with a high OCD level I think this would be a good idea.

and if anyone would make such item I would buy it at once.

User avatar
HoolyHoo
Posts: 766
Joined: Sat Jul 09, 2016 9:34 pm
Has thanked: 206 times
Been thanked: 741 times

Re: Idea: HoolyHoo PCB Template

Post by HoolyHoo » Fri Apr 20, 2018 2:34 pm

Sasherz wrote:
Fri Apr 20, 2018 1:07 pm
I am sorry if this is the wrong place to ask.
But Im not good in 3D Design, I dont even have a 3D Printer myself.

long story short.
I bout this PCB from HoolyHoo
https://sudomod.com/forum/viewtopic.php?f=38&t=5665
I tryed drilling on a test case to see if it would fit, but, it ended up crookid.
Cause of the height from the PCB to the shell has a few mm gap, and its enough to throw the drilling off, making the buttons not look neet on the backside.
som the holes might end up being higher up, lower, closer together, etc.

so my idea for a template is.

It doesnt need to be more than a few mm thick and would sit inside the GB shell for accurate drilling.
it might sound useless, but for the perfectionist with a high OCD level I think this would be a good idea.

and if anyone would make such item I would buy it at once.
Here is a drill guide that will work with that bracket. Mark one side then flip it over and mark the other two holes.
DrillGuide.zip
(7.49 KiB) Downloaded 322 times

Sasherz
Posts: 77
Joined: Wed Jul 26, 2017 2:50 pm
Location: Norway
Has thanked: 6 times
Been thanked: 6 times

Re: Idea: HoolyHoo PCB Template

Post by Sasherz » Fri Apr 20, 2018 5:07 pm

now, who want money from me?
well if anyone could print and send it to me

User avatar
MegaLoop
Posts: 23
Joined: Mon Feb 26, 2018 5:19 am
Has thanked: 6 times
Been thanked: 7 times

Re: Idea: HoolyHoo PCB Template

Post by MegaLoop » Sun Apr 22, 2018 6:35 pm

I was also curious about this. Printed template definitely helpful!

Marijom
Posts: 3
Joined: Thu Aug 23, 2018 10:28 am
Contact:

Idea HoolyHoo PCB Template

Post by Marijom » Sun Aug 26, 2018 5:38 pm

No, was just a picture to represent something of what it might look like , just an idea, doesnt even hav to look like that either, but if i can get the tools ill try my hand at making my own representation.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest