[Guide] Graceful shutdown switch without Pololu [RETIRED]
- alien0matic
- Posts: 102
- Joined: Wed Jun 08, 2016 7:20 am
- Has thanked: 15 times
- Been thanked: 23 times
Re: [Guide] Graceful shutdown switch without Pololu
Thanks Camble, I got it all going now. Gate and Source were switched. Seems like there are a lot of different pinouts for those transistors.
Now everything works just fine, the DMG is closed again and I'm happy
PS: What GPIO would be better then GPIO4?
Now everything works just fine, the DMG is closed again and I'm happy
PS: What GPIO would be better then GPIO4?
- Camble
- Posts: 885
- Joined: Thu May 05, 2016 2:31 am
- Location: Scotland
- Has thanked: 269 times
- Been thanked: 488 times
Re: [Guide] Graceful shutdown switch without Pololu
@alien0matic Glad to hear it. I found that most MOSFETs I used had the gate on pin 2, but the JFETs seemed to have the gate on pin 3. Some datasheets displayed a nice image of the package, making it easy to identify pins. Some showed the pinout from above, others showed the pinout from below. So... definitely worth taking the time to familiarise yourself with the particular JFET you are using. Maybe your 2N5460 was packaged by a different manufacturer and has a different pinout.
Do you have the link for the JFET you bought? I'd like to check it out to make sure others don't get stuck with the same issue.
Any regular BCM pin should be fine. https://pinout.xyz/
I think I used 22.
Do you have the link for the JFET you bought? I'd like to check it out to make sure others don't get stuck with the same issue.
Any regular BCM pin should be fine. https://pinout.xyz/
I think I used 22.
- alien0matic
- Posts: 102
- Joined: Wed Jun 08, 2016 7:20 am
- Has thanked: 15 times
- Been thanked: 23 times
Re: [Guide] Graceful shutdown switch without Pololu
I bought those transistors. The gate is on the left pin when you look at the photo. http://www.ebay.de/itm/172276817585
- Camble
- Posts: 885
- Joined: Thu May 05, 2016 2:31 am
- Location: Scotland
- Has thanked: 269 times
- Been thanked: 488 times
Re: [Guide] Graceful shutdown switch without Pololu
That is unusual. Any datasheet I've seen for the 2N5460 has the gate on pin 3. Do you know what the logo on the JFET is?
Unfortunately I don't speak German.
Unfortunately I don't speak German.
Re: [Guide] Graceful shutdown switch without Pololu
Hi Camble, I have an adafruit 1000c recharger and want to handle a graceful shutdown, would this part be relevant in my situation as well? If so how do i go about ordering a pcb from you?Camble wrote:For those who aren't in the Discord chat room, I ordered up the first revision of the PCB today. If all goes well, I'll be able to supply it with a switch, or without for you to solder your DMG-01 switch onto.
- Camble
- Posts: 885
- Joined: Thu May 05, 2016 2:31 am
- Location: Scotland
- Has thanked: 269 times
- Been thanked: 488 times
Re: [Guide] Graceful shutdown switch without Pololu
@jazzy Yes, this circuit is designed for use with the Adafruit PowerBoost supplies. I'm currently waiting on delivery of an early design of the PCB and will start a sales thread when I have finished testing. Probably still be a few weeks as the boards are coming from the US.
Re: [Guide] Graceful shutdown switch without Pololu
Ah nice, i'll keep a look out for it, i'm based in Scotland too so I don't know if that makes postage any easier, also might have another Scottish modder looking for a board too if you need numbers
- Popcorn
- Trailblazer
- Posts: 354
- Joined: Thu May 05, 2016 12:58 am
- Location: Berlin
- Has thanked: 29 times
- Been thanked: 71 times
Re: [Guide] Graceful shutdown switch without Pololu
I have updated my original thread and the battery monitor github readme.md and have pointed them to this thread as the new recommended hardware solution over the pololu. I will be testing this circuit and if all goes well, I'll completely abandon support of the pololu and push this as the proper method to use. Thanks for your work, @Camble!
Who is online
Users browsing this forum: No registered users and 1 guest