Circuit Gem "Build Guide" kinda

Get help with your VMµ build here!
Post Reply
User avatar
gambino37
Posts: 217
Joined: Fri Oct 20, 2017 7:17 am
Has thanked: 4 times
Been thanked: 63 times

Circuit Gem "Build Guide" kinda

Post by gambino37 » Mon Apr 08, 2019 1:22 pm

While I'm no Wermy by any stretch of the imagination, it seems as though a Circuit Gem build guide is a highly sought after commodity. Ill give it my best shot now. At least it will be a start. I'm waiting on another gem kit in the mail and if anyone wants more detailed photos Ill be doing them with that build. I'm not going to focus too much on the Pi side of things as that is pretty much covered by Kite in his guide.

What I will say for starters is that if you are using a transparent case, a Dremel and good cutting bits are almost a necessity if you want a good finished look. The cutting bits remove material and don't leave that white "ghosting" look. Obviously if you have an opaque case, this is less of a necessity and a good pair of flush cutters may suffice. Links to my favorite three:

https://www.amazon.com/gp/product/B0002 ... UTF8&psc=1
https://www.amazon.com/gp/product/B0002 ... UTF8&psc=1
https://www.amazon.com/gp/product/B0002 ... UTF8&psc=1

STL for button holder bracket:
Button Holder.stl
(53.79 KiB) Downloaded 552 times
For the back of the case, start by removing everything marked in red. All the way down to the surface of the case.

Image


Leave yourself a small border around the opening for the door to rest on. (disregard the other holes for a second. We will get to those later)

Image


You should also trim down the "legs" on the door. You can do this one of two ways, either hold it and do it by hand or tape the door back on the case and use the rest of the case as a guide for how much to trim off.

Image

Now for the front. Not much to remove here. So for the two red marks at the top of the following picture, I wasnt sure if anything for sure was to be removed there in the end. Just pay attention to those areas.

Image

There is also a peg right under where the screen goes that needs to be removed. I apologize for not showing this clearly as I already had my screen in at this point. NOTE!!!! DO NOT LOSE THAT BEIGE LOOKING LITTLE PEG FROM THE D-PAD! that thing falls out every time you mess with it. You can put the screen in now if you want. As long as its flush with the bottom edge of the opening it's perfect. See my awesome looking arrows for hot glue locations. You don't need much, the screen really isn't going to move on you.

Image

Image

Now that the Pi and PCB are in you are pretty good for the front.

Image

FYI I did strip the PiZero. I actually did it after it was soldered to the PCB. If you are going to do this, BE VERY CAREFUL. I know it probably wasn't the smartest way to do it. I just used flush cutters and snipped small pieces off one at a time. Keep in mind that all three of the inputs have legs that go through the Pi PCB so if you have already soldered it to the Gem board, you cant really use Chip Quik or anything like that. Patience is a virtue with this.

Image

So back to the extra holes in the back. I made a little assembly for the "shoulder" buttons. However, I have giant hands and this thing is tiny so I decided to put them when it would be the most comfortable.

Image

The bracket serves three purposes. It holds the door on the case, holds the buttons (duh), and takes away very precious real estate inside the case for a bigger battery! Hooray! This step is obviously optional, I just wanted to share.

Image

Thats about it!

Image

My build only has a 350mAh battery so it was pretty easy fitting it in there. I also have an 800mAh battery, just waiting for the kit in the mail.

Image

Image

I hope this helps anyone who was looking for something like this. Its not perfect by any means, but at least its something!
Last edited by gambino37 on Thu Jul 18, 2019 5:34 pm, edited 1 time in total.

User avatar
smoscar01
Posts: 20
Joined: Fri Jun 01, 2018 8:21 pm
Has thanked: 12 times
Been thanked: 10 times

Re: Circuit Gem "Build Guide" kinda

Post by smoscar01 » Mon Apr 15, 2019 7:50 pm

Nice job!

How comfortable are the L/R buttons there?

User avatar
gambino37
Posts: 217
Joined: Fri Oct 20, 2017 7:17 am
Has thanked: 4 times
Been thanked: 63 times

Re: Circuit Gem "Build Guide" kinda

Post by gambino37 » Mon Apr 15, 2019 8:04 pm

I thought they were better there. Haven't them on top almost forces your thumbs to support the thing by the bottom. To each his own I guess.

User avatar
rodocop
Posts: 1723
Joined: Mon Aug 22, 2016 3:14 pm
Location: Saskatchewan
Has thanked: 606 times
Been thanked: 608 times

Re: Circuit Gem "Build Guide" kinda

Post by rodocop » Wed Apr 17, 2019 3:12 pm

Nice little guide!

User avatar
wermy
Site Admin
Posts: 1346
Joined: Tue May 03, 2016 8:51 pm
Has thanked: 620 times
Been thanked: 1322 times
Contact:

Re: Circuit Gem "Build Guide" kinda

Post by wermy » Mon Apr 29, 2019 3:05 pm

Nice, thanks for sharing! Clever to use the battery door screw to hold the L/R buttons :)
ImageImageImageImage

sandog
Posts: 123
Joined: Fri Oct 26, 2018 8:17 pm
Has thanked: 9 times
Been thanked: 6 times

Re: Circuit Gem "Build Guide" kinda

Post by sandog » Tue Jul 16, 2019 7:49 pm

Did I miss the stl for the back buttons

User avatar
JayCanuck
Posts: 19
Joined: Sat May 12, 2018 3:06 am
Has thanked: 71 times
Been thanked: 2 times

Re: Circuit Gem "Build Guide" kinda

Post by JayCanuck » Tue Jul 16, 2019 9:08 pm

Very clean and some great tips for future builds. Any chance you'd be willing to share the STL for the back frame; looks really handy!
Also, based on your build, any recommendations on L/R button size/height?

User avatar
gambino37
Posts: 217
Joined: Fri Oct 20, 2017 7:17 am
Has thanked: 4 times
Been thanked: 63 times

Re: Circuit Gem "Build Guide" kinda

Post by gambino37 » Wed Jul 17, 2019 8:22 am

Ill upload the STL this weekend. I think the buttons I used on this one are 5 or 6 mm tall. I'm not positive really. I just bought one of the packs on Amazon that had a variety of sizes.

User avatar
gambino37
Posts: 217
Joined: Fri Oct 20, 2017 7:17 am
Has thanked: 4 times
Been thanked: 63 times

Re: Circuit Gem "Build Guide" kinda

Post by gambino37 » Thu Jul 18, 2019 5:35 pm

STl is uploaded. Near the top of the post. Enjoy!

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest