All of sudden buttons presses by itself even after fresh sd image and no rubbers attached. Config of buttons in emulation station impossible. Any ideas what can be the reason for this?
Update: When configuring D-pad -> D-PAD UP enters by itself AXIS 0+ but no joystick is physically connected.
Buttons fault Kite Circuit sword 1.3
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: Usa
- Been thanked: 171 times
- Contact:
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Buttons fault Kite Circuit sword 1.3
Can you try performing the arduino update, see how that goes: https://github.com/kiteretro/Circuit-Sw ... controller
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: Usa
- Been thanked: 171 times
- Contact:
Re: Buttons fault Kite Circuit sword 1.3
Arduino flashed OK but issue still persist. When running python Circuit-Sword/cs-configure.py if JOY 1 is enabled refreshing the page shows movement on X with nothing connected. If disabled an only joy2 is on everything is ok. Any ideas?
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Buttons fault Kite Circuit sword 1.3
Do you have any joys connected (or plan to)? If not then disable them
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: Usa
- Been thanked: 171 times
- Contact:
Re: Buttons fault Kite Circuit sword 1.3
The plan was to use dual joystick, GB shell prepared. Is it a board/component fault ?
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Buttons fault Kite Circuit sword 1.3
When the joysticks are plugged in, what do the readings of the analog values show? Are they wildly changing?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: Usa
- Been thanked: 171 times
- Contact:
Re: Buttons fault Kite Circuit sword 1.3
Only the 1st joy changes values by itself between 830 to 990 and if you keeps pressing enter to refresh eventually it jumps to ridiculous -30000
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Buttons fault Kite Circuit sword 1.3
Yeah something not really right there.. could you show pictures of how you wired up the joystick?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Who is online
Users browsing this forum: No registered users and 1 guest