Aluminum Case

Show off your completed Game Boy Zero, or post your build logs here!
arbinshire
Posts: 25
Joined: Sun Jun 05, 2016 6:51 pm
Has thanked: 2 times
Been thanked: 16 times

Re: Aluminum Case

Post by arbinshire » Sun Mar 29, 2020 6:09 pm

IMG_0416.jpg
Back Buttons
IMG_0416.jpg (6.89 MiB) Viewed 535 times
Final picture showing back buttons.

This was perhaps the easiest build to put together. Everything just screws together and the only place I put hot-glue was to hold the speaker in place. It looks like there's going to be something to hold the speaker in place, but I didn't receive that with my purchase. I had to use an older of Kite's CM3 board from early 2018 since my two November 2018 boards don't work and refuse to boot.

I usually don't name my builds, but this particular one has a whovian theme, "Cyber Boy."

Dividion
Posts: 81
Joined: Fri Mar 30, 2018 5:42 am
Has thanked: 54 times
Been thanked: 64 times

Re: Aluminum Case

Post by Dividion » Sun Mar 29, 2020 8:54 pm

arbinshire wrote:
Sun Mar 29, 2020 6:09 pm
Final picture showing back buttons.

This was perhaps the easiest build to put together. Everything just screws together and the only place I put hot-glue was to hold the speaker in place. It looks like there's going to be something to hold the speaker in place, but I didn't receive that with my purchase. I had to use an older of Kite's CM3 board from early 2018 since my two November 2018 boards don't work and refuse to boot.

I usually don't name my builds, but this particular one has a whovian theme, "Cyber Boy."
Looks great!

Which button caps did you end up using on the back? I ordered one of the cases a few weeks ago, since I still had an unassembled CSO (also from 2018) and I think I've got everything for it except those. Thanks!
Check out my store for GBZ boards and accessories: http://pocketadventures.com

arbinshire
Posts: 25
Joined: Sun Jun 05, 2016 6:51 pm
Has thanked: 2 times
Been thanked: 16 times

Re: Aluminum Case

Post by arbinshire » Sun Mar 29, 2020 10:36 pm

I used some leftover MintyPi buttons. I took a 1500 grit sandpaper to the back side of it to remove the lettering and smooth it a bit.

Hivetyrant
Posts: 15
Joined: Thu Jun 21, 2018 3:33 pm
Has thanked: 2 times
Been thanked: 8 times

Re: Aluminum Case

Post by Hivetyrant » Mon Mar 30, 2020 6:06 am

I went ahead and ordered one as well, Will probably transfer my CS to it and replace the plastic guts with a rpi 3A+ which I have almost got working!

Ziploc99
Posts: 33
Joined: Sun Jun 17, 2018 10:02 am
Has thanked: 25 times
Been thanked: 9 times

Re: Aluminum Case

Post by Ziploc99 » Tue Apr 07, 2020 1:24 pm

Looks good. Did you use a 3d print to hold the battery in place? It's mentioned on the site, wondering if you used Helder's megabat and how that is placed in the shell.

Also, if you have a 3d printer, there are a few "glueless speaker holder's" floating around that fix the speaker in place without glue (obviously).

arbinshire
Posts: 25
Joined: Sun Jun 05, 2016 6:51 pm
Has thanked: 2 times
Been thanked: 16 times

Re: Aluminum Case

Post by arbinshire » Tue Apr 07, 2020 11:41 pm

I used a generic battery and velcro and affixed it to the battery door. I'll have to check on the 3d printed battery holder.

Hivetyrant
Posts: 15
Joined: Thu Jun 21, 2018 3:33 pm
Has thanked: 2 times
Been thanked: 8 times

Re: Aluminum Case

Post by Hivetyrant » Wed Apr 08, 2020 10:16 am

Just thought I'd mention I was a bit of a dumb dumb and somehow didn't pay attention to the shell only being compatible with the "older" circuit sword (CM3 not the new CM3+) and so the one I received from the last batch technically doesn't fit but I'm going to grind down the heatsink block and make it fit as it's such a beautiful shell.

arbinshire
Posts: 25
Joined: Sun Jun 05, 2016 6:51 pm
Has thanked: 2 times
Been thanked: 16 times

Re: Aluminum Case

Post by arbinshire » Wed Apr 08, 2020 10:38 pm

It should be relatively easy to mill it down. Make sure you use kapton tape everywhere.

User avatar
mrdude42
Posts: 88
Joined: Sun May 15, 2016 10:04 am
Location: New York City
Has thanked: 214 times
Been thanked: 25 times
Contact:

Re: Aluminum Case

Post by mrdude42 » Mon Jun 08, 2020 4:28 pm

Ah man I really want one but they're sold out… :(

djascher
Posts: 122
Joined: Sat Jan 27, 2018 9:21 pm
Location: Toronto
Has thanked: 47 times
Been thanked: 19 times

Re: Aluminum Case

Post by djascher » Mon Jun 08, 2020 4:42 pm

How much and from where and are these still available?

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest