Collecting information on alternative displays - please contribute

[johnthenlnja]

Anyone seen this screen before? Does it need to be converted to 5V?

Based on the suggestion by @DannyJK I converted my screen with the same board

[BuToNz]

So I ordered one of these:
https://www.aliexpress.com/item/Newest- ... 98031.html

Turned up a couple of days back. Nice quality and fits well into the case with a little trimming of the PCB. I also removed the touch screen.

Much better than the BW screen, default text is readable and no fuzzy/blurriness. Aspect ratio is obviously a little less ideal but I'll compensate with a thicker bezel at the bottom of the LCD cut out.

Here's an attempt at showing the picture quality...

[Valadone]

So I ordered one of these:
https://www.aliexpress.com/item/Newest- ... 98031.html

Turned up a couple of days back. Nice quality and fits well into the case with a little trimming of the PCB. I also removed the touch screen.

Much better than the BW screen, default text is readable and no fuzzy/blurriness. Aspect ratio is obviously a little less ideal but I'll compensate with a thicker bezel at the bottom of the LCD cut out.

Here's an attempt at showing the picture quality...

Is it really a 1920*1080 3.5" screen =O ?

And hi everyone, i bought a new screen, because my other screen don't want to run and i don't know whyand the pcb is too big.

I received this one today ( the variant 7 ) but when i tried to make it run in 5V nothing happen ... Someone can give me some tips to help me run this screen through 5V ? Do i need to change the code to display on the component for the rpi 0 ?

P_20170220_204924.jpg (822.72 KiB) Viewed 9800 times

P_20170220_204955.jpg (863.99 KiB) Viewed 9800 times

Orange => white
yellow => yellow
Red => +
darkblue => -

TY !

[BuToNz]

It will take a 1080p signal (Actually doesn't look bad!) but the native is 480x320.

[Valadone]

Kk very nice so

[milhouse]

Hi All

Just for Info, in my efforts for modding a GB to GBZ, the screen I bought from Amazon, I think. Will check.

This screen works without modding the the PCB with link cable etc. Powers ok from 5 Volts, see below pics.

image.jpeg (560.88 KiB) Viewed 9771 times

image.jpeg (716.96 KiB) Viewed 9771 times

image.jpeg (567.76 KiB) Viewed 9771 times

[Valadone]

Hmmm big question, to make the raspberry pi 0 run on composite video output, we have to change the config.txt of recalbox, retropi, ... to change the output ? True ?

Because if we have to do that, 0 tutorials indicate it...

[BuToNz]

Hmmm big question, to make the raspberry pi 0 run on composite video output, we have to change the config.txt of recalbox, retropi, ... to change the output ? True ?

Because if we have to do that, 0 tutorials indicate it...

Recalbox box does require changing the config.txt, Retropie should work without any changes. Here for Recalbox: https://youtu.be/_MtN_s4tVK0?t=4m49s

[smoothpapacool]

Has anyone tried this display?
http://www.gearbest.com/lcd-led-display ... tml?wid=21
If not, is it possible? I'm new to all of this and learning along the way. I've already got a BW 3.5", but was thinking this might work and fit a little better in the DMG case.

Thoughts? Suggestions?

Thanks,
SPC

[Valadone]

Hmmm big question, to make the raspberry pi 0 run on composite video output, we have to change the config.txt of recalbox, retropi, ... to change the output ? True ?

Because if we have to do that, 0 tutorials indicate it...

Recalbox box does require changing the config.txt, Retropie should work without any changes. Here for Recalbox: https://youtu.be/_MtN_s4tVK0?t=4m49s

Seriously... Never forgot to say to a noob in electronic to check those files ...

The BW screen is running very well now ! Thanks a lot man ! And now just try to make it running on the RPi0 and on the other screen