[For Sale, Preorder] DMG pre-cut cases

kubino · Post by **kubino** » Sat Jul 22, 2017 10:39 am

Chrisagu28 wrote: ↑
Sat Jul 22, 2017 3:16 am
Did you use a standard countersink bit when you did your test? I would love to have that little taper/countersunk holes. It would put the cherry on top of my GBZ shell I get from you.

it was done with the same 1.2mm bit, but bigger radius. I have few angle bits, but I'm affraid it won't be much noticable due to sharp edges.

Elmafioso90 · Post by **Elmafioso90** » Sat Jul 22, 2017 12:56 pm

Kubino, did you receive the cases you ordered for us?

kubino · Post by **kubino** » Sun Jul 23, 2017 12:19 am

Elmafioso90 wrote: ↑
Sat Jul 22, 2017 12:56 pm
Kubino, did you receive the cases you ordered for us?

I just received some. Unfortunately one clear case comes without buttons. But rest looks fine and I'll start with processing this week.

Chrisagu28 · Post by **Chrisagu28** » Sun Jul 23, 2017 12:24 am

You mentioned you only received some? did they all not show up? I am curious if all the grey ones showed up.

kubino · Post by **kubino** » Sun Jul 23, 2017 12:34 am

Chrisagu28 wrote: ↑
Sun Jul 23, 2017 12:24 am
You mentioned you only received some? did they all not show up? I am curious if all the grey ones showed up.

I received 2x clear, 1x transparent orange, 4x white, 2x grey

Elmafioso90 · Post by **Elmafioso90** » Sun Jul 23, 2017 2:51 am

kubino wrote: ↑
Sun Jul 23, 2017 12:34 am
I received 2x clear, 1x transparent orange, 4x white, 2x grey

How lucky, my black one is still missing hahaha.

Anyway, I will PM you later to arrange everything and to send you the payment.

Thanks, dude!

kubino · Post by **kubino** » Mon Jul 24, 2017 1:56 am

One clear with countersink done. I was affraid of the result but seems OK. What do you thing ?

SpoilerShow

: P_20170724_095334.jpg (1.54 MiB) Viewed 8257 times

: P_20170724_095313.jpg (2.23 MiB) Viewed 8257 times

Chrisagu28 · Post by **Chrisagu28** » Mon Jul 24, 2017 4:04 am

I think it looks pretty good! Good to see progress on the shells are being made too. Looking forward to getting one of these!

I am liking the clear too. Someone will have a good looking build with it!

Post by **dryja123** » Mon Jul 24, 2017 4:05 pm

kubino wrote: ↑
Mon Jul 24, 2017 1:56 am
One clear with countersink done. I was affraid of the result but seems OK. What do you thing ?

I ordered a clear and I think that looks great!

Chrisagu28 wrote: ↑
Mon Jul 24, 2017 4:04 am
I think it looks pretty good! Good to see progress on the shells are being made too. Looking forward to getting one of these!

I am liking the clear too. Someone will have a good looking build with it!

Me!

kubino · Post by **kubino** » Tue Jul 25, 2017 2:41 am

L/R tactile buttons with 3d printed bracket :

L/R buttonsShow

: P_20170725_102650.jpg (1.25 MiB) Viewed 8216 times

: P_20170725_103316.jpg (1.29 MiB) Viewed 8216 times

: P_20170725_102712.jpg (1.32 MiB) Viewed 8216 times

[For Sale, Preorder] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Re: [interest check] DMG pre-cut cases

Who is online