WII U RASPBERRY PI 3 FINISHED

[Misturbubles]

Curiousity question:

How difficult would it be to remove the hdmi ports from the lcd driver board and the Pi, and replace them with a FPC? This way there aren't any bulky ports taking up space. Would it be worth it?

Not a beginners task but not overly difficult. I already did this for one of my builds (not posted yet) and it works! Saves a ton of space too.
Edit: worth it, in my opinion, but very easy to destroy the solder pads

Thank you very much for your response. I may take a shot at it, not sure tho. I'd hate to destroy either board.

[Misturbubles]

Could anyone please help me with something?

Tbh, I have zero experience in writing code but have managed to figure out the basic understand on the Teensy code. I was looking at Banjo's Teensy code and I can't seem to figure out were "mode" and "led" belong on the Teensy itself. Where are they?

Also, I would like to add a "start+select" button. How would that look like in the code? Or should just leave it as is?

Please forgive my ignorance in code. Learning in progress. Thank you in advance for your time!!

[Misturbubles]

Could anyone please help me with something?

Tbh, I have zero experience in writing code but have managed to figure out the basic understand on the Teensy code. I was looking at Banjo's Teensy code and I can't seem to figure out were "mode" and "led" belong on the Teensy itself. Where are they?

Also, I would like to add a "start+select" button. How would that look like in the code? Or should just leave it as is?

Please forgive my ignorance in code. Learning in progress. Thank you in advance for your time!!

Nvm, I think I figured it out. Somehow I kept skipping over the very first few lines. Keeping everything as is.

[Misturbubles]

I'm working in my audio circuit. When everything is connected, I only get this loud buzzing coming out of the speakers.

Could anyone give me some advice on what happening? Any help out be greatly appreciated.

[merward11]

The link to order the board: https://oshpark.com/shared_projects/PxxdBxo7

thanks just ordered, do you have any ebay links for leds and buttons? or a pic of your connected with buttons leds and resistors on?

Buttons I used:
http://www.ebay.com/itm/10pcs-Tact-Swit ... 2749.l2649

LEDs:
http://www.ebay.com/itm/0805-SMD-SMT-LE ... SwZ8ZW6aHH

Resistors
http://www.ebay.com/itm/20-pcs-of-selec ... knuDv4E6Hg

I don't have a picture of it all set up but it would look really similar to banjokazooie board



Also here's a wiring setup for the board:

working through my build on the wii u button/LED board you've marked 6 terminals up to connect to the teensy - which terminals do the connect to?

[Ryohazouki]

hello everyone.

I introduce myself, my name is salah, 35 years old, marry, 3 children.
I find myself on the other side of the plane. in a city that we call "paris".

I was doing research on the net, to create a portable console with a raspberry pi 3.

as I have not found anything in French, we do a search in English, I'm falling on your beautiful sitwed.

I'm sorry, but my English is very bad.
I will wish to obtain information.

for the bottom buttons, can we use the same process as for the other buttons?

https://www.ebay.fr/itm/10pcs-FFC-FPC-C ... A0b8c7db6- 11a6-11e8-86f1-74dbd180fbe2 7Cparentrq%%% 3A95322d211610abc61ff5e66cfff9b71a 7Ciid% 3A1 & _trksid = p2481888.c100675.m4236

second question. what is the plate you used to hold the screen?

thank you my friends.

[Misturbubles]

@banjokazooie, you release for m5 version a custom PCB for front button.

I search the same for indicate : low batt, full batt, charge batt and powered indicator.

Where i can design this (i search MG Design but... nothing).

Big thanks

The board is my custom design

You used 271s here. Would be it ok to use 221s? If not, what alternatives could I use instead of 271s (my bundle didn't come with 271s)? Any advise would be greatly appreciated!!

[banjokazooie]

@banjokazooie, you release for m5 version a custom PCB for front button.

I search the same for indicate : low batt, full batt, charge batt and powered indicator.

Where i can design this (i search MG Design but... nothing).

Big thanks

The board is my custom design

You used 271s here. Would be it ok to use 221s? If not, what alternatives could I use instead of 271s (my bundle didn't come with 271s)? Any advise would be greatly appreciated!!

271s ? All SMD`s are in 0805 size, easy to hand solder. You could use smaller 0603.

[phdirnou]

@banjokazooie
I think Misturbubles speaks about the capacity (Ohm) of the resistors. In your M5 built you use 0805 SMD's and the capasity was 270 Ohm.
How did you read the battery capacity in your M5 built and display it via the LED's on the Home PCB?
I've already built and soldered most of the parts, except the Home PCB. CJnyc3 posted a picture of this with all the connections. Did you read the battery capacity with your Teensy?

[Misturbubles]

The board is my custom design

You used 271s here. Would be it ok to use 221s? If not, what alternatives could I use instead of 271s (my bundle didn't come with 271s)? Any advise would be greatly appreciated!!

271s ? All SMD`s are in 0805 size, easy to hand solder. You could use smaller 0603.

Thank you for the response. Sorry for not being clear on that. I was talking about the ones soldered next to the leads. In the picture, I see 0 and 271. I have some 220 resistors. Would those work? Any and all advice is greatly appreciated!!