[For Sale, Preorder] DMG pre-cut cases

[Brag0n]

Kubino, that looks sweet, indeed!
Is the revision done, and when are you doing colour combination pictures?

[edwardthehuman]

6mm bracket with extruded buttons in clear case :

P_20180208_142216.jpg

I have to say feeling is much better than on 3d printed buttons.

You might not know the answer but is that going to align on Kite's CS 4-button back?

[Dos8088]

I’m interested in a couple cases to use with Kites CS Board, four holes in front, and large buttons in back. One with clear blue in front and black for the back, another with clear orange front and black for the back. I can just buy a couple black cases from you to make the switch if I need to.

[nickzick]

Might be a stupid question but can anyone tell me how to solder the l1 l2 r1 r2 buttons included here to an for the kite saio board? Thanks in advance.

[neolith]

Might be a stupid question but can anyone tell me how to solder the l1 l2 r1 r2 buttons included here to an for the kite saio board? Thanks in advance.

Do you want to know how soldering works or which wires to connect?

If it's the soldering, look here.
If it's the wiring, look here.

[nickzick]

Might be a stupid question but can anyone tell me how to solder the l1 l2 r1 r2 buttons included here to an for the kite saio board? Thanks in advance.

Do you want to know how soldering works or which wires to connect?

If it's the soldering, look here.
If it's the wiring, look here.

I know hier soldering works, I just don‘t know how to connect the wires. Kite uses buttons with just two pins to solder to. In this order there are 4 pins at each button.
Hope that you guys understand what I‘d like to say:-)

[kubino]

I know hier soldering works, I just don‘t know how to connect the wires. Kite uses buttons with just two pins to solder to. In this order there are 4 pins at each button.
Hope that you guys understand what I‘d like to say:-)

those are standard tactile switches where 2 and 2 are common, check with multimeter. It's enought if you connect only 2 of them (the correct ones )

Solder 2 which are closest together and use this as GND :

P_20180216_210701.jpg (1.42 MiB) Viewed 6986 times

Hope it helps as because of this I dissasembled ny GBZ

[neolith]

I know hier soldering works, I just don‘t know how to connect the wires. Kite uses buttons with just two pins to solder to. In this order there are 4 pins at each button.
Hope that you guys understand what I‘d like to say:-)

Ah, I see - now I understand.

I don't know what hardware you have, but it's usually like this:
On buttons with four pins the ones across from each other (the way they bend) are usually the same connection. You could bend them towards each other and solder them together and the button would work just the same. But you don't have to, you can use just one of each of the pins. I wouldn't worry too much about it – if you get it wrong, you'll create a shortcut. With a button it's not that bad, because the button will register as always pressed (normally pressing the button creates the shortcut). But if you do worry, you can check with a multimeter first.

edit: I type too slow, kubino was faster.

[dryja123]

I know hier soldering works, I just don‘t know how to connect the wires. Kite uses buttons with just two pins to solder to. In this order there are 4 pins at each button.
Hope that you guys understand what I‘d like to say:-)

Instructions and explanations on how to do it are found on Kite's GitHub. His link is in his FAQ and his sales threads.

[Pyro4fun]

I’d like to order a clear case, I ordered Kite’s new sword.
I want to use two big buttons on the back (dmg buttons).
I have PM’d you once already, let me know what I owe you and I’ll pre order it. Thanks