Please Help ! Problems with PD035VX2 Wiring with KYV-N2 V7

Hardware-related questions that don't fit into any of the specialized hardware categories go here.
Post Reply
Rowi
Posts: 30
Joined: Sun Jan 27, 2019 1:41 pm
Been thanked: 1 time

Please Help ! Problems with PD035VX2 Wiring with KYV-N2 V7

Post by Rowi » Sat Apr 13, 2019 5:01 am

Hi after a recommendation I bought https://de.aliexpress.com/item/WISECOCO ... 4c4dXeZs6r this from alienexpress.
After 3 months it finally arrived.

I was told to wire the yellow wire to my pi Zero - but there is no yellow wire. Also the board is 12V (I think it should 5V shouldn't it?)

What can I do to fix the 12V Problem ? Is there a manual for this board ?
If you have RGB Video - is there even a yellow wire because as you see on the photograph there is none :-(
Attachments
IMG_20190413_125515.jpg
IMG_20190413_125515.jpg (1.56 MiB) Viewed 592 times
IMG_20190413_125505.jpg
IMG_20190413_125505.jpg (2.3 MiB) Viewed 592 times

User avatar
ABH
Posts: 187
Joined: Sat May 28, 2016 7:01 pm
Location: Qatar
Has thanked: 77 times
Been thanked: 111 times

Re: Please Help ! Problems with PD035VX2 Wiring with KYV-N2 V7

Post by ABH » Sat Apr 13, 2019 5:25 am

Use this “AV1” wire for the composite Input, i bought recently something similar it should work off 5v give it a try..
0071F030-CFAA-4623-8F45-C6D24F66BD91.jpeg
0071F030-CFAA-4623-8F45-C6D24F66BD91.jpeg (507.87 KiB) Viewed 590 times

Rowi
Posts: 30
Joined: Sun Jan 27, 2019 1:41 pm
Been thanked: 1 time

Re: Please Help ! Problems with PD035VX2 Wiring with KYV-N2 V7

Post by Rowi » Sat Apr 13, 2019 6:13 am

delete
Last edited by Rowi on Sat Apr 13, 2019 6:47 am, edited 1 time in total.

Rowi
Posts: 30
Joined: Sun Jan 27, 2019 1:41 pm
Been thanked: 1 time

Re: Please Help ! Problems with PD035VX2 Wiring with KYV-N2 V7

Post by Rowi » Sat Apr 13, 2019 6:14 am

av1 -> video pi zero
if I would use a pi3 b+ where would I put it then?

It seems it does not matter which 12V and which GND I use... But should I connect 1 GND to my controllerboard (tinkerboy) and 1 to raspi as shown in the graph. If yes should I use both grounds from the Power supply part of the board?
Attachments
v2.0_screen_wiring.jpg
v2.0_screen_wiring.jpg (1.09 MiB) Viewed 580 times

Rowi
Posts: 30
Joined: Sun Jan 27, 2019 1:41 pm
Been thanked: 1 time

Re: Please Help ! Problems with PD035VX2 Wiring with KYV-N2 V7

Post by Rowi » Sat Apr 13, 2019 9:21 am

If it will not work - what can I do to get my board working with only 12 V? or is it possible to convert the 5V to 12?

Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests