Gambino's Swords

gambino37 · Post by **gambino37** » Tue Apr 23, 2019 12:23 pm

Messed around with resin printing carts.

And what you do with the leftover case halves

Dual Joystick Build (Back buttons courtesy of AntFJ)

jwh02017 · Post by **jwh02017** » Tue Apr 23, 2019 3:10 pm

Great looking builds. Do you have any pics of the inside? What kind of battery are you using?

gambino37 · Post by **gambino37** » Tue Apr 23, 2019 3:23 pm

jwh02017 wrote: ↑
Tue Apr 23, 2019 3:10 pm
Great looking builds. Do you have any pics of the inside? What kind of battery are you using?

I only use Helder's Megabat.

lord_of_misrule · Post by **lord_of_misrule** » Tue Apr 23, 2019 3:57 pm

gambino37 wrote: ↑
Tue Apr 23, 2019 3:23 pm

jwh02017 wrote: ↑
Tue Apr 23, 2019 3:10 pm
Great looking builds. Do you have any pics of the inside? What kind of battery are you using?

I only use Helder's Megabat.

This is an awesome build! What kind of buttons are these on the back?? Would love to get some for my Sword!

-LoM

gambino37 · Post by **gambino37** » Tue Apr 23, 2019 4:03 pm

HoolyHoo slim button kit.

MrErickson · Post by **MrErickson** » Tue Apr 23, 2019 9:43 pm

On the black back with the Start/Select buttons, how well are they working for you? I did the same on my CS build and they sadly are not making reliable contact with the pads. I'm debating toying with the 3D model as I think it's the top side not making good contact or swapping them out for soft tactile buttons.

gambino37 · Post by **gambino37** » Wed Apr 24, 2019 4:24 am

MrErickson wrote: ↑
Tue Apr 23, 2019 9:43 pm
On the black back with the Start/Select buttons, how well are they working for you? I did the same on my CS build and they sadly are not making reliable contact with the pads. I'm debating toying with the 3D model as I think it's the top side not making good contact or swapping them out for soft tactile buttons.

Did you have the PCB that was meant for them from AntFJ? Mine work perfectly.

MrErickson · Post by **MrErickson** » Wed Apr 24, 2019 6:15 am

gambino37 wrote: ↑
Wed Apr 24, 2019 4:24 am

MrErickson wrote: ↑
Tue Apr 23, 2019 9:43 pm
On the black back with the Start/Select buttons, how well are they working for you? I did the same on my CS build and they sadly are not making reliable contact with the pads. I'm debating toying with the 3D model as I think it's the top side not making good contact or swapping them out for soft tactile buttons.
Did you have the PCB that was meant for them from AntFJ? Mine work perfectly.

That's probably it then, I used Kite's back board that came with my CS, I tested with my multimeter and it looked to be connecting but once installed it isnt as reliable.

kopas · Post by **kopas** » Wed Apr 24, 2019 10:04 am

Man, you just dumped a ton of awesome in the show-off corner... Is that a little 3D printed collet on the headphone jack? If so, got an STL?

gambino37 · Post by **gambino37** » Wed Apr 24, 2019 10:54 am

kopas wrote: ↑
Wed Apr 24, 2019 10:04 am
Man, you just dumped a ton of awesome in the show-off corner... Is that a little 3D printed collet on the headphone jack? If so, got an STL?

Yea I figured I may as well since I haven't in a long time. https://www.thingiverse.com/thing:3195418
I really had to drill the shit out of it to get it to fit properly.

Gambino's Swords

Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Re: Gambino's Swords

Who is online