[For Sale] $7 Game Boy Zero Controller PCB W/ Optional Audio $20 (Worldwide) SOLD OUT

[Helder]

That psp joystick is really cute and I'd definitely like it since I was thinking to put a trackpoint stick (from a lenovo laptop keyboard) into the back of my gbz to better use games that run under scummvm. I already programmed and reversed the pins for trackpoint for teensy 2.o boards in the past so I have that ps2 part ready but now this psp joy really appeals me even more! Will it be something you were planning to put right below the 4 directing cross button?

Again really in for a full controller and will buy a psp joystick as well!!

Tent

Honestly I'm not sure where you would mount it but somewhere around the Dpad would be ideal, the pads being there means you can just use wires and put it where you see fit.

[gargoyle67]

@Helder,
Just wondering if your onboard audio has any noise suppression circuitry ? Or would I need to add some ferrite beads to the +- leads ?

Thanks.

[Helder]

@Helder,
Just wondering if your onboard audio has any noise suppression circuitry ? Or would I need to add some ferrite beads to the +- leads ?

Thanks.

You will have to add them yourself but they are cheap and you can get the ones that look like resistors and put them inline to the speaker, I'll add them in the next batch though.

A little bad news for everyone, my supplier has had an issue with the atmega32u4 and I have had to cancel the order and am awaiting a refund. I'm contacting some other suppliers and seeing what I can get at a fair price and getting DHL shipping to get them here ASAP. This will likely delay the All in One boards another week but hopefully not.

[gargoyle67]

@Helder,
Just wondering if your onboard audio has any noise suppression circuitry ? Or would I need to add some ferrite beads to the +- leads ?

Thanks.

You will have to add them yourself but they are cheap and you can get the ones that look like resistors and put them inline to the speaker, I'll add them in the next batch though.
[/b]

Oh thanks that's cool, Does it matter what Ohm Resistance they are at all ? I'm looking at these>
http://www.ebay.co.uk/itm/50-Pcs-52-Ohm ... SwT6pVxEWM

[Helder]

@Helder,
Just wondering if your onboard audio has any noise suppression circuitry ? Or would I need to add some ferrite beads to the +- leads ?

Thanks.

You will have to add them yourself but they are cheap and you can get the ones that look like resistors and put them inline to the speaker, I'll add them in the next batch though.
[/b]

Oh thanks that's cool, Does it matter what Ohm Resistance they are at all ? I'm looking at these>
http://www.ebay.co.uk/itm/50-Pcs-52-Ohm ... SwT6pVxEWM

Should be fine since most speakers we are using don't go beyond 8 ohms and that is 52 ohms.

[zuul]

I am so amazed by the board(s) you created! However, I am really confused now on how pre-ordering is supposed to work.

Being afraid to miss out I'd also like to state that I would - if this is the correct way to do it - pre-order two of the all in one boards (EU based)!

[FootHouse]

A little bad news for everyone, my supplier has had an issue with the atmega32u4 and I have had to cancel the order and am awaiting a refund. I'm contacting some other suppliers and seeing what I can get at a fair price and getting DHL shipping to get them here ASAP. This will likely delay the All in One boards another week but hopefully not.

No worries, Helder, everyone here appreciates the effort you're putting into the boards, I'm sure. The amount of time that the all in one boards will save complete novices like me is more than the week or so delay.

[Boondoggle]

I am so amazed by the board(s) you created! However, I am really confused now on how pre-ordering is supposed to work.

Being afraid to miss out I'd also like to state that I would - if this is the correct way to do it - pre-order two of the all in one boards (EU based)!

I might be wrong but I don't think Helder has offered a 'Pre-order" in this thread. The last thing I read in regards to this was...

"If they sell out I will setup a preorder where people who prepay will get one guaranteed and I will order the total amount of the preorders so no more selling out as I have no real way of gauging the amount of people interested"

So if I read that right, he will give people the opportunity to pre-order on the second wave of these.

[Helder]

I am so amazed by the board(s) you created! However, I am really confused now on how pre-ordering is supposed to work.

Being afraid to miss out I'd also like to state that I would - if this is the correct way to do it - pre-order two of the all in one boards (EU based)!

I might be wrong but I don't think Helder has offered a 'Pre-order" in this thread. The last thing I read in regards to this was...

"If they sell out I will setup a preorder where people who prepay will get one guaranteed and I will order the total amount of the preorders so no more selling out as I have no real way of gauging the amount of people interested"

So if I read that right, he will give people the opportunity to pre-order on the second wave of these.

I will put them up for sale publicly once I have all parts to assemble a complete board for sale so it might be an extra week because of the atmega delay.

Once this first batch sells out I will open up pre orders for a second batch as I have explained that will guarantee a board/s for whoever misses this first run.

[deadpixel52]

I am so amazed by the board(s) you created! However, I am really confused now on how pre-ordering is supposed to work.

Being afraid to miss out I'd also like to state that I would - if this is the correct way to do it - pre-order two of the all in one boards (EU based)!

I might be wrong but I don't think Helder has offered a 'Pre-order" in this thread. The last thing I read in regards to this was...

"If they sell out I will setup a preorder where people who prepay will get one guaranteed and I will order the total amount of the preorders so no more selling out as I have no real way of gauging the amount of people interested"

So if I read that right, he will give people the opportunity to pre-order on the second wave of these.

I will put them up for sale publicly once I have all parts to assemble a complete board for sale so it might be an extra week because of the atmega delay.

Once this first batch sells out I will open up pre orders for a second batch as I have explained that will guarantee a board/s for whoever misses this first run.

Does that mean the first batch is yet to sell out? Would I be able to put my name down for one?