Difference between revisions of "GBZ Misc Hardware"
m (added hdmi cable section) |
m (→3D Printed Parts: added a bunch more parts I found on thingiverse) |
||
| Line 38: | Line 38: | ||
Button wells: [http://sudomod.com/wp-content/uploads/2016/07/gbz_button_wells.stl_.zip stl files] or [http://sudomod.com/forum/viewtopic.php?f=3&t=923 buy] | Button wells: [http://sudomod.com/wp-content/uploads/2016/07/gbz_button_wells.stl_.zip stl files] or [http://sudomod.com/forum/viewtopic.php?f=3&t=923 buy] | ||
| + | |||
| + | Screen Bracket with X/Y buttons: [https://www.thingiverse.com/thing:2033239 Thingiverse] | ||
| + | |||
| + | Alternate 2-part Screen Bracket with X/Y buttons & drill guide: [https://www.thingiverse.com/thing:2311662 Thingiverse] | ||
| + | |||
| + | Alternate Top screw bracket with HDMI holder: [https://www.thingiverse.com/thing:2319250 Thingiverse] | ||
| + | |||
| + | Drill guide for centered back buttons: [https://www.thingiverse.com/thing:2466985 Thingiverse] | ||
| + | |||
| + | Fake cart to hold a full-size SD card reader: [https://www.thingiverse.com/thing:2102808 Thingiverse] | ||
| + | |||
| + | Holder for a dremel-free battery install: [https://www.thingiverse.com/thing:1418834 Thingiverse] | ||
| + | |||
| + | Button Wells with integrated drill guide: [https://www.thingiverse.com/thing:2173083 Thingiverse] | ||
| + | |||
| + | Cart shell: [https://www.thingiverse.com/thing:13605 Thingiverse] | ||
== HDMI Cables == | == HDMI Cables == | ||
Thin ribbon cable: [https://www.ebay.com/itm/252508906577?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT ebay] | Thin ribbon cable: [https://www.ebay.com/itm/252508906577?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT ebay] | ||
Latest revision as of 02:42, 4 December 2017
Contents
GPIO PWM Audio for Raspberry Pi Zero
150 Ohm resistor, 270 Ohm resistor, 10nF capacitor, and a 33nF capacitor (another 10nF will work fine as well if that’s easier to find)
L/R Buttons
If you want to use tactile switches in the rear screwholes like the original GBZ, you'll need something similar to this: http://www.amazon.com/9-5mm-Momentary-Tactile-Button-Switch/dp/B008420WOA or this
Replacement case
A replacement case for the gameboy can be found here.
Audio Jack
In case you can not use the audio jack of the original GBZ board here is a replacement.
Power Switch
If you don't have the power switch from the GBZ board or are unable to desolder it you can use this switch.
Due to space constraints in the Gameboy DMG case, it may be advisable to use a replacement switch with terminals on the side, instead of the one listed above. Here, here, and here are some choices.
Micro SD Card
32 Gb micro SD card to install RetroPie on and roms.
Prototype PCB
Protoytype PCB to create power distribution board or GPIO sound output for the RPi Zero.
Step-Up Modules (Voltage Regulators)
0-5V to 5V - 1,89$
5V to 12V - 1,90$
Wide Range Steup or Step Down regulators
Battery leads/JST Plug
Trying to wire a custom battery up to a PowerBoost? Need JST 2.0 PH type leads. Here
3D Printed Parts
Power Switch holder: stl files or buy
GBA Cart slot holder: stl files or buy
Top Screw brackets: stl files or buy
Button wells: stl files or buy
Screen Bracket with X/Y buttons: Thingiverse
Alternate 2-part Screen Bracket with X/Y buttons & drill guide: Thingiverse
Alternate Top screw bracket with HDMI holder: Thingiverse
Drill guide for centered back buttons: Thingiverse
Fake cart to hold a full-size SD card reader: Thingiverse
Holder for a dremel-free battery install: Thingiverse
Button Wells with integrated drill guide: Thingiverse
Cart shell: Thingiverse
HDMI Cables
Thin ribbon cable: ebay
