Difference between revisions of "GBZ Misc Hardware"
m (→Step-Up Modules (Voltage Regulators)) |
m (added 3d printed parts section) |
||
Line 29: | Line 29: | ||
== Battery leads/JST Plug == | == Battery leads/JST Plug == | ||
Trying to wire a custom battery up to a PowerBoost? Need JST 2.0 PH type leads. [https://www.aliexpress.com/store/product/50-SETS-Mini-Micro-JST-2-0-PH-2-Pin-Connector-Plug-with-Wires-Cables-120MM/1360129_32824363436.html Here] | Trying to wire a custom battery up to a PowerBoost? Need JST 2.0 PH type leads. [https://www.aliexpress.com/store/product/50-SETS-Mini-Micro-JST-2-0-PH-2-Pin-Connector-Plug-with-Wires-Cables-120MM/1360129_32824363436.html Here] | ||
+ | |||
+ | == 3D Printed Parts == | ||
+ | Power Switch holder: [http://sudomod.com/wp-content/uploads/2016/09/gbz_power_switch_brace.stl_.zip stl files] or [http://sudomod.com/forum/viewtopic.php?f=3&t=1482 buy] | ||
+ | |||
+ | GBA Cart slot holder: [http://sudomod.com/wp-content/uploads/2016/09/gbz_gba_cartridge_mount.zip stl files] or [http://sudomod.com/forum/viewtopic.php?f=3&t=1483 buy] | ||
+ | |||
+ | Top Screw brackets: [http://sudomod.com/wp-content/uploads/2016/07/gbz_top_screw_bracket_with_guides.stl_.zip stl files] or [http://sudomod.com/forum/viewtopic.php?f=3&t=789 buy] | ||
+ | |||
+ | Button wells: [http://sudomod.com/wp-content/uploads/2016/07/gbz_button_wells.stl_.zip stl files] or [http://sudomod.com/forum/viewtopic.php?f=3&t=923 buy] |
Revision as of 00:20, 1 December 2017
Contents
GPIO PWM Audio for Raspberry Pi Zero
150 Ohm resistor, 270 Ohm resistor, 10nF capacitor, and a 33nF capacitor (another 10nF will work fine as well if that’s easier to find)
L/R Buttons
If you want to use tactile switches in the rear screwholes like the original GBZ, you'll need something similar to this: http://www.amazon.com/9-5mm-Momentary-Tactile-Button-Switch/dp/B008420WOA or this
Replacement case
A replacement case for the gameboy can be found here.
Audio Jack
In case you can not use the audio jack of the original GBZ board here is a replacement.
Power Switch
If you don't have the power switch from the GBZ board or are unable to desolder it you can use this switch.
Due to space constraints in the Gameboy DMG case, it may be advisable to use a replacement switch with terminals on the side, instead of the one listed above. Here, here, and here are some choices.
Micro SD Card
32 Gb micro SD card to install RetroPie on and roms.
Prototype PCB
Protoytype PCB to create power distribution board or GPIO sound output for the RPi Zero.
Step-Up Modules (Voltage Regulators)
0-5V to 5V - 1,89$
5V to 12V - 1,90$
Wide Range Steup or Step Down regulators
Battery leads/JST Plug
Trying to wire a custom battery up to a PowerBoost? Need JST 2.0 PH type leads. Here
3D Printed Parts
Power Switch holder: stl files or buy
GBA Cart slot holder: stl files or buy