V3 20190501 Can't shutdown?

Having trouble with your mintyPi build? Post your questions here!
User avatar
wermy
Site Admin
Posts: 1341
Joined: Tue May 03, 2016 8:51 pm
Has thanked: 612 times
Been thanked: 1318 times
Contact:

Re: V3 20190501 Can't shutdown?

Post by wermy » Sat May 04, 2019 10:46 pm

gambino37 wrote:
Sat May 04, 2019 10:20 pm
I was having the shutdown problems before doing that anyway. And also on the first image. I talked to you already on Instagram about mine. Lots of derps with my first V3 build so I may not be the prime candidate for troubleshooting. I just figured I would throw my hat in the ring once I saw other people were having the same issues.
Ah that's right, I didn't put 2 and 2 together with your username. :) If it was happening prior to this image then I'd definitely check your TX pin as Helder suggested. For anyone else having this issue, if you could double-check that you don't see this behavior in the previous image that would be helpful. You can grab it here: http://www.mediafire.com/file/bc66b24cv ... v3.gz/file
ImageImageImageImage

NeonJesterface
Posts: 18
Joined: Thu Apr 04, 2019 5:26 pm
Has thanked: 3 times

Re: V3 20190501 Can't shutdown?

Post by NeonJesterface » Sun May 05, 2019 3:02 am

I've been having this problem with a fresh image, just tried again after specifically making sure I went through and disabled ftp and the same thing did happen. I'll pick up another card when I can, but I just flashed the old v3 image and its doing the same thing

User avatar
Helder
Trailblazer
Trailblazer
Posts: 2687
Joined: Thu May 05, 2016 8:33 am
Location: Fall River, MA
Has thanked: 1380 times
Been thanked: 3039 times

Re: V3 20190501 Can't shutdown?

Post by Helder » Sun May 05, 2019 8:20 am

Check the TX voltages to see if they are going low or not then we can try to investigate other things that might be causing this. You can also hold down the power button to force it to shut off once it gets to that point.
My Sale Threads:

Retro PSU, 3.5A output!


Chat with me and other members


Don't contact me about obtaining my board files (as you will not get them). Don't contact me about any of my boards if they are sold out, they will be restocked as soon as I can get them.


Don't support thieves like ckliang who copied my AIO to resell and is now cloning the mintyPi, support the original creators and not the thieves!

NeonJesterface
Posts: 18
Joined: Thu Apr 04, 2019 5:26 pm
Has thanked: 3 times

Re: V3 20190501 Can't shutdown?

Post by NeonJesterface » Sun May 05, 2019 11:01 pm

With power on I'm getting 3.28V and at the screen I get stuck at I'm getting 0.2mV, and the power button will not force it to shut off

User avatar
Helder
Trailblazer
Trailblazer
Posts: 2687
Joined: Thu May 05, 2016 8:33 am
Location: Fall River, MA
Has thanked: 1380 times
Been thanked: 3039 times

Re: V3 20190501 Can't shutdown?

Post by Helder » Mon May 06, 2019 2:49 am

NeonJesterface wrote:
Sun May 05, 2019 11:01 pm
With power on I'm getting 3.28V and at the screen I get stuck at I'm getting 0.2mV, and the power button will not force it to shut off
So the TX goes high then goes low and stays there? Are you powering thus from the power board or the Pi itself?

The power button does nothing at all without the powerboard attached so your testing without it is going to give you bad results and we will likely give you advice that might not work if we don't know this.
My Sale Threads:

Retro PSU, 3.5A output!


Chat with me and other members


Don't contact me about obtaining my board files (as you will not get them). Don't contact me about any of my boards if they are sold out, they will be restocked as soon as I can get them.


Don't support thieves like ckliang who copied my AIO to resell and is now cloning the mintyPi, support the original creators and not the thieves!

NeonJesterface
Posts: 18
Joined: Thu Apr 04, 2019 5:26 pm
Has thanked: 3 times

Re: V3 20190501 Can't shutdown?

Post by NeonJesterface » Mon May 06, 2019 12:00 pm

Yes, Im only using the mintypi as its built, so Im on the battery and powerboard I got from you guys, and the 3.28 was just what I was getting steady with the power on, I can go back and check as the shutdown happens

NeonJesterface
Posts: 18
Joined: Thu Apr 04, 2019 5:26 pm
Has thanked: 3 times

Re: V3 20190501 Can't shutdown?

Post by NeonJesterface » Wed May 22, 2019 1:48 am

And I finally got another SD card, still doing the same thing

NeonJesterface
Posts: 18
Joined: Thu Apr 04, 2019 5:26 pm
Has thanked: 3 times

Re: V3 20190501 Can't shutdown?

Post by NeonJesterface » Sat Jun 01, 2019 3:57 am

I'm completely stumped here, should I try and reflow anything? or try replacing the pi?

User avatar
LilTrublMakr
Posts: 233
Joined: Sun Aug 05, 2018 6:39 am
Has thanked: 23 times
Been thanked: 92 times
Contact:

Re: V3 20190501 Can't shutdown?

Post by LilTrublMakr » Sun Jun 02, 2019 3:01 pm

Just to make sure:

You are using the power board and off battery. When triggering the halls sensor, it goes through the process but does not cut the power? And the power button turns it on but won't turn it off when held?

User avatar
gambino37
Posts: 147
Joined: Fri Oct 20, 2017 7:17 am
Has thanked: 5 times
Been thanked: 38 times

Re: V3 20190501 Can't shutdown?

Post by gambino37 » Sun Jun 02, 2019 3:21 pm

Mine does the exact same thing.

Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests